483706
7
Zoom out
Zoom in
Previous page
1/8
Next page
The normal installation is like the above
Condition 1: Powering the Antenna by STB or Digital TV
Step 1.Take out the main unit AS 07
Step 2.Take out the multi-directional base. Fixed it on the wooden pole or at a wall (as figure, please
check the follow paragraph for information)
Step 3.fix the main unit to the multi-directional base
Step 4.Take the Coaxial(IEC male to F female) Cable connect the IEC Male end to the IEC Female
End of your Set Top Box or TV Set and F female the F-Female End of the AS 07.
Please note: all the connection should be fixed. It is recommended that you should had a
water-drop loop at the end of cable before entering your home.)
Step 5Adjust the orientation of AS 07. (Normally speaking, the signal is horizontal direction.)
Condition 2: Powering the antenna by AC adaptor( in cases that there is no DC
power out from the STB or Digital TV, you need to do this installation)
Tips for correct Antenna Adjustment
When you finished the installation, you can use your Set Top Box to check the signal strength
and quality. If the quality is not good enough to have good picture, you can move the antenna
to get the best reception position, when you find the best position , please fixed it. If not, you
can change the reception direction by adjust the main unit
Indoor /Outdoor Wall Mounted installation
If you want to hook this unit onto a brick wall or RC
wall, please follow the steps bellow
Before the following step, please make sure that you
have enough protection when you try to drill on the
wall.
Step 1. Mark the fixing position with pencil or another
pen( please use the multi-directional base to
mark the position)
Step 2.Take the electric drill, using 5.8mm drill bit( please note , when you use the electric drill, you
should better to wear the protection device. And the drill bit should be fixed, otherwise there
will be a serious injuring happened when the bit is broken or loose). Drill the depth to 35mm.
Then clean the hole.
Please note , if you want to install On a wooden wall , you don´t need to drill holes
before!
Step 3.Take out the plastic pole, using hammer to ham it into the hole made by step1
Step 4.Take out the screws attached, using screw driver to fix these screws through the base and fix it
on the wall.
Step 5. Fix the main unit on the multi-directional base
Step 6.Take the Coaxial(IEC male to IEC female) Cable connect the IEC Male end to the IEC Female
End of your Set Top Box or TV Set and IEC female to “Receiver” on power inserter. Take
another coaxial (F male to IEC male) cable, connect the F-male End to the F-Female End of the
AS 07 and IEC male to “Antenna” on Power inserter. Please note: all the connection should be
fixed. It is recommended that you should had a water-drop loop at the end of cable before
entering your home. (if your installation is outdoor)
Step 7.Take out the AC-DC Adaptor, connect the barrel end to the DC input of Power inserter, AC end
to the AC Outlet. Please note use only supplied AC adaptor
Step 8.Adjust the orientation of AS 07. (Normally speaking, the signal is horizontal direction.)
3
Final
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zehnder AS 07 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zehnder AS 07 in the language / languages: German as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info