517530
7
Zoom out
Zoom in
Previous page
1/36
Next page
7
User’s manual
EN
Do not tamper with, sidestep, eliminate or bypass the safety devices installed. The non-observance of this requirement may cause serious
personal injury or death.
Keep the lawn mower in conditions of maximum ef ciency by carrying out the maintenance operations provided for by the Manufacturer.
Proper maintenance will allow obtaining the best performances and longer operating times.
Before carrying out any maintenance and adjustments disconnect the electric power supply. The user must ensure that all the necessary
safety conditions are in place, especially when working on the lower part of the lawn mower, and must follow the Manufacturer’s procedures
and instructions.
Use the personal protection devices prescribed for by the Manufacturer, in particular, always wear protective gloves when working on the
cutting blade.
Before replacing the batteries, always remove the blade.
Make sure the air openings of the power supply unit are free and clear of residuals.
In order to not irreversibly damage the electric and electronic parts, do not wash the robot with high-pressurised water and do not immerse
it in water, partially or completely, since it is not watertight.
Only quali ed persons, having the necessary technical expertise and skill, should attempt to work on or repair this robot. Failure to observe
these requirements could result in serious injury.
Any work to be performed on the charging station must be carried out with the plug of the power cord disconnected.
Replace any worn or deteriorated parts with original spare parts to ensure proper functionality and safety.
The robot cannot be used without the upper cover; if the mechanical parts of the robot are damaged, they must be replaced.
Any routine or extraordinary maintenance (e.g. battery replacement) must be performed by an authorised service centre.
The Manufacturer shall not be held liable if non-original spare parts are used.
Never use and recharge the robot in explosive and/or ammable environments.
SAFETY DEVICES
1. Bumpers
The bumper sensor is enabled if the robot strikes a solid object higher than 10 cm (3.94 "). This sensor will stop the movement in that direction
and move backwards to avoid the obstacle.
2. Inclinometer
If the robot works on a slope which is steeper than the maximum limit, or tips over, this safety device will stop the cutting blade.
3. Emergency stop switch
Located on the control panel, red in colour. Pressing this button at any time during operation will immediately stop the movement of the mower
and the rotation of the blade will stop within 2 seconds.
4. Over-current protection
The motors (blade and wheels) are monitored continuously during operation for any situation that may cause them to overheat. If this occurs
in the wheel motor, the robot will attempt to move in the opposite direction. If the over-current persists, the robot will stop and signal an error.
If the cutting motor overheats, then there are two types of intervention. If the parameters fall within the rst range, the robot will perform the
manoeuvres to unblock the cutting blade. If the over-current is below the protection range, the robot will stop and signal a motor error.
5. No signal of the sensor
If there is no signal on the perimeter cable, the robot will automatically stop.
6. Lifting sensor
In the event that the robot is lifted from the ground by the central handle, the cutting blade will stop rotating.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZCS 9L2BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZCS 9L2BL in the language / languages: English as an attachment in your email.

The manual is 10,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ZCS 9L2BL

ZCS 9L2BL User Manual - Dutch - 56 pages

ZCS 9L2BL User Manual - Dutch - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info