24639
20
Zoom out
Zoom in
Previous page
1/28
Next page
20
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below.
During machine operation it is possible that the “End” light flashes to indicate that the machine is not working.
4 flashes = door open
2 flashes = the water is not drained
1 flash = there is no water filling
Once the problem has been eliminated, press the Start/Pause button to restart the programme. If after all checks, the
problem persists, contact your local Service Centre.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
The machine does not start
Possible causes
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no supply at the socket
The main fuse or the fuse in the plug has blown.
The selector dial is not correctly positioned and the Start/Pause button
has not been depressed.
The delay start has been selected.
The machine does not fill
Ensure the water tap is open.
The filter in the inlet hose is blocked.
The inlet hose may be squashed or kinked.
The door has not been closed.
The machine fills then empties
immediately
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
The machine does not empty and/or
does not spin
The drain hose may be squashed or kinked.
The option RINSEHOLD or NOSPIN has been selected.
The drain pump may be blocked.
The drain hose extension, if fitted, is not correct. Follow the
instructions for connecting to the waste.
The drainage system pipes are blocked.
The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.
There is water on the floor
Too much detergent or unsuitable detergent has been used (creates too
much foam).
Check whether there are any leaks from one of the inlet hose fittings. It
is not always easy to see this as the water runs down the hose; check to
see if it is damp.
The drain hose may be damaged or not securely positioned.
The cap on the emergency emptying hose has not been replaced after
cleaning the pump or not fully screwed up.
The drainage system pipes are blocked.
Unsatisfactory washing results
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct wash programme has not been selected.
Too much laundry has been placed in the drum.
35.293.010….ZWF1421.qxd 30/3/06 17:25 Página 20
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zanussi ZWF1421W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZWF1421W in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info