24579
23
Zoom out
Zoom in
Previous page
1/28
Next page
23
Important !
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
In case of moving out the same precautions as per
paragraph “The dangers of freezing” must be taken i.e.
the residual water in the hoses must be pumped out.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to suitable existing tap with the drain
hose discharging into a sink.
The appliance has one inlet hose, with female 3/4” BSP
thread connector. If this connection is not compatible
with the plumbing of the existing installation, a variety
of connectors are available from good hardware stores
and plumbers merchants to suit most domestic
plumbing. Any alteration to your existing plumbing
must be carried out by a competent person, or qualified
plumber.
Installation on a Suspended Floor
Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.
Unpacking
All transit bolts and packing must be removed
before using the appliance
You are advised to keep all the packaging for re-use in
case the appliance has to be transported again.
Unscrew and remove the three rear transit bolts
(using a spanner).
Lay the machine gently on its back, making sure
that the hoses are not squashed.
We suggest a polystyrene angle bracket from the
packing is placed on the floor before tilting it back
to avoid the hoses being spacers.
Carefully remove the polyethylene bags located at
the base of the machine by pulling them toward the
centre of the machine.
Place the machine in an upright position and
remove the three plastic spacers.
AL009
2
1
P0287
P0018
P0002
P0001
Plug the 3 holes with the plastic plugs which you
can find in the envelope containing the instruction
booklet.
35.292.996…ZWF 1112 W.qxd 30/3/06 13:56 Página 23
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zanussi ZWF1112W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZWF1112W in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info