Manual Zanussi ZTE 283 (page 24 of 60) (English, German, Dutch, French)

447428

Zoom out

Zoom in

1/60

audible confirmation of:

• cycle end

• anti-crease phase start and end

• cycle interruption

• error

TIME

after setting the Time programme. You can select a

programme duration from 10 mins to 2 hrs in 10-mi-

nute steps.

DELAY START

allows to delay the start of a drying programme from

minimum of 30 min. to maximum of 20 hours. Press

the Delay Start button repeatedly until the desired delay

start is shown on the display

Setting child lock

The child lock can be set to prevent a programme being

accidentally started or a programme in operation being

accidentally changed. The child lock function locks all

buttons and the programme selector. The child lock can

be activated or deactivated by holding down the DELI-

CATE and LONG ANTI-CREASE buttons simultaneously

for 5 seconds.

– Before programme is started: Appliance cannot be

used

– After programme is started: Programme in operation

cannot be changed

The icon

appears in the display to indicate that the

child safety device is activated.

The child safety device is not deactivated once the pro-

gramme comes to an end.

If you want to set a new programme, you must first de-

activate the child safety device.

Starting the programme

Press the Start/Pause button. The programme starts.

The programme progress is shown by elapsing dry time

on the LCD.

Changing programme

To change a programme which is running, first cancel it

by turning the programme selector dial to

. Select the

new programme and press the START/PAUSE button.

The programme can no longer be changed directly

once the programme has started. If nevertheless

there is an attempt to change the programme on the pro-

gramme knob, the programme progress display and the

maintenance indicators flash. If an option button (exclud-

ing the BUZZER button) is pressed,

appears on the

display. The drying programme is not however affected

by this (laundry protection).

Drying cycle complete / removing laundry

Once the drying cycle is complete, the display shows the

anti-crease icon and flashing as well as warning

lamps: FILTER and FULL TANK. If the BUZZER button has

been pressed, an acoustic signal sounds intermittently for

about one minute.

The drying cycles are automatically followed by an

anti-crease phase which lasts around 30 minutes.

The drum rotates at intervals during this phase. This keeps

the laundry loose and free of creases. The laundry can be

removed at any time during the anti-crease phase. (The

laundry should be taken out towards the end of the anti-

crease phase at the latest to prevent creases from form-

ing.)

1. Open door.

2. Before removing the laundry, remove fluff from the

micro-fine filter. It is best to use a damp hand for this

purpose. (See “Cleaning and maintenance” chapter.)

3. Remove laundry.

Turn the programme selector to

off.

5. Close the door.

After each use

• Clean the filters.

• Empty the water reservoir.

Cleaning and maintenance

Cleaning fluff filters

The filters collect all the fluff which accumulates during

drying. To ensure that the dryer works perfectly, the fluff

filters (fine filters and fluff filters) must be cleaned after

each drying cycle.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZTE 283 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 7,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zanussi ZTE 283 Manual

Product: