Manual Zanussi ZGS 783 ICTX (page 15 of 48) (English, German, Dutch, French)

76629

Zoom out

Zoom in

1/48

Installation

Warning! The following instructions about

installation, connection and maintenance must be

carried out by qualified personnel in compliance with

standards and local regulations in force.

Gas Connection

It is necessary that the connection to the gas mains are

carried out by means of an AGB tap. Choose fixed con-

nections or use a flexible pipe in AGB (stainless steel) in

compliance with the regulation in force. If you use flexible

metallic pipes, be careful they do not come in touch with

mobile parts or they are not squeezed. Also be careful

when the hob is put together with an oven.

The connection must be done according to regulation

NBN D 5I.003.

Important! Make sure that the gas supply pressure of the

appliance obeys the recommended values. The adjustable

connection is fixed to the comprehensive ramp by means

of a threaded nut G 1/2". All the components shown in the

figure have already been assembled in the factory. The

appliance, before leaving the factory, has been tested in

order to give you the best results.

1 End of shaft with nut

2 Washer

3 Elbow

Flexible nonmetal pipes connection:

If it is possible to easily control the connection in its full

area, you can use a flexible pipe. Tightly attach the flexible

pipe by clamps.

Liquid gas: use the rubber pipe holder. Always engage the

gasket. Then continue with the gas connection. The flexi-

ble pipe is prepared for apply when:

– it can not get hot more than room temperature, higher

than 30°C;

– it is no longer than 1500 mm;

– it shows no throttles;

– it is not subject to traction or torsion;

– it does not get in touch with cutting edges or corners;

– it can be easily examined in order to check its condi-

tion.

The control of preservation of the flexible pipe consists in

checking that:

– it does not show cracks, cuts, marks of burnings on the

two ends and on its full length;

– the material is not hardened, but shows its correct

elasticity;

– the fastening clamps are not rusted;

– expired term is not due.

If one or more defects are visible, do not repair the pipe,

but replace it.

Important! When installation is complete, make sure that

the seal of each pipe fitting is correct. Use a soapy

solution, not a flame!

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors and re-

place them with the ones which are necessary for the

type of gas you use (see table in Technical Data sec-

tion).

4. Assemble the parts, follow the same procedure back-

wards.

5. Replace the rating plate (it is near the gas supply

pipe) with the one for the new type of gas supply.

You can find this plate in the package supplied with

the appliance.

If the supply gas pressure is changeable or different from

the necessary pressure, you must fit an applicable pres-

sure adjuster on the gas supply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZGS 783 ICTX in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zanussi ZGS 783 ICTX Manual

Product: