Manual Zanussi ZGO98520BA (page 7 of 16) (English)

766174

Zoom out

Zoom in

1/16

Liquid gas

Use the rubber pipe holder for liquid gas. Always

engage the gasket. Then continue with the gas

connection.

The flexible pipe is prepared for apply when:

• it can not get hot more than room temperature,

higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting edges or

corners;

• it can be easily examined in order to make sure

its condition.

The control of preservation of the flexible pipe

consists in checking that:

• it does not show cracks, cuts, marks of burnings

on the two ends and on its full length;

• the material is not hardened, but shows its

correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not repair the

pipe, but replace it.

WARNING! When installation is

complete, make sure that the seal of

each pipe fitting is correct. Use a

soapy solution, not a flame!

INJECTORS REPLACEMENT

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors

and replace them with the ones which are

necessary for the type of gas you use (see

table in "Technical Data" chapter).

4. Assemble the parts, follow the same procedure

backwards.

5. Attach the label with the new type of gas

supply near the gas supply pipe. You can find

this label in the package supplied with the

appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you must fit

an applicable pressure adjuster on the gas supply

pipe.

ADJUSTMENT OF MINIMUM LEVEL

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the bypass

screw position (A).

5. If you change:

• from natural gas G20 20 mbar to liquid gas,

fully tighten the bypass screw in.

• from liquid gas to natural gas G20 20 mbar,

undo the bypass screw approximately 1/4

of a turn (1/2 of a turn for Multi Crown

burner).

WARNING! Make sure the flame does

not go out when you quickly turn the

knob from the maximum position to the

minimum position.

ELECTRICAL CONNECTION

• Make sure that the rated voltage and type of

power on the rating plate agree with the voltage

and the power of the local power supply.

• This appliance is supplied with a mains cable. It

has to be supplied with a correct plug which

can hold the load that the rating plate rates.

Make sure that you install the plug in a correct

socket.

• Always use a correctly installed shockproof

socket.

• Make sure that there is an access to the mains

plug after the installation.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• There is a risk of fire when the appliance is in

connection with an extension cable, an adapter

or a multiple connection. Make sure that the

ground connection agrees with the standards

and regulations.

• Do not let the power cable to heat up to a

temperature higher than 90° C.

Make sure that you connect the blue

neutral cable to the terminal with a

letter "N" on it. Connect the brown (or

black) phase cable to the terminal

which has a letter "L". Keep the phase

cable connected at all times.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZGO98520BA in the language / languages: English as an attachment in your email.

The manual is 0,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zanussi ZGO98520BA

Zanussi ZGO98520BA User Manual - German, Dutch, French - 52 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zanussi ZGO98520BA Manual

Product: