332219

Zanussi zgg 755 alu Manual

17
Zoom out
Zoom in
Previous page
1/52
Next page
• Disconnect the appliance from the elec-
trical supply, before you do the mainte-
nance work or you clean it.
• The electrical mains terminal is live.
• Make electrical mains terminal free of volt-
age.
• Install correctly to give anti-shock protection.
• A loose and incorrect mains plug and socket
connections can make the terminal become
too hot.
• A qualified electrician must install the clamp-
ing connections correctly.
• Use a strain relief clamp on cable.
• Use the correct mains connection cable and
replace the damaged mains cable with appli-
cable cable. Speak to your local Service
Force Centre.
• The appliance must have the electrical instal-
lation which lets you disconnect the appli-
ance from the mains at all poles with a con-
tact opening width of minimum 3 mm.
• If the fixing bracket is near to the terminal
block, always make sure the connection ca-
ble does not come in contact with the edge
of the bracket.
• You must have correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), ground leakage
trips and contactors.
Disposal of the appliance
• To prevent the risk of physical injury or dam-
age
– Disconnect the appliance from the power
supply.
– Cut off the mains cable where it connects
with the appliance and discard it.
– Flat the external gas pipes if there are fit-
ted.
– Speak to your local authorised facilities for
disposal of your appliance.
Installation
Warning! The following instructions about
installation, connection and maintenance
must be carried out by qualified personnel in
compliance with standards and local
regulations in force.
Gas Connection
It is necessary that the connection to the gas
mains are carried out by means of an AGB tap.
Choose fixed connections or use a flexible pipe
in AGB (stainless steel) in compliance with the
regulation in force. If you use flexible metallic
pipes, be careful they do not come in touch
with mobile parts or they are not squeezed. Al-
so be careful when the hob is put together with
an oven.
The connection must be done according to
regulation NBN D 5I.003.
Important! Make sure that the gas supply
pressure of the appliance obeys the
recommended values. The adjustable
connection is fixed to the comprehensive ramp
by means of a threaded nut G 1/2". All the
components shown in the figure have already
been assembled in the factory. The appliance,
before leaving the factory, has been tested in
order to give you the best results.
1
2
3
1
End of shaft with nut
2
Washer
3
Elbow
Liquid gas: use the rubber pipe holder. Always
engage the gasket. Then continue with the gas
17
www.zanussi.com
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zanussi zgg 755 alu at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi zgg 755 alu in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info