Manual Zanussi ZDT16020 FA (page 35 of 80) (English, German, Dutch, French)

628656

Zoom out

Zoom in

1/80

• Pull out the upper basket.

• To disengage the spray arm from the basket, press the spray arm upwards in the direction indicated by

the lower arrow and simultaneously turn it clockwise.

• Wash the spray arm under running water. Use a thin pointed tool, e.g. toothpick, to remove particles of

soil from the holes.

• To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by

the lower arrow and simultaneously turn it counterclockwise until it locks into place.

EXTERNAL CLEANING

• Clean the appliance with a moist soft cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive cleaning

pads or solvents.

INTERNAL CLEANING

• Carefully clean the appliance, including the

rubber gasket of the door, with a soft damp

cloth.

• If you regularly use short duration programmes,

these can leave deposits of grease and

limescale inside the appliance. To prevent this,

we recommend to run long duration

programmes at least 2 times per month.

• To maintain the performance of your appliance

at its best, we recommend to use monthly a

specific cleaning product for dishwashers.

Follow carefully the instructions on the

packaging of the product.

TROUBLESHOOTING

If the appliance does not start or it stops during

operation. Before you contact an Authorised

Service Centre, check if you can solve the problem

by yourself with the help of the information in the

table.

WARNING! Repairs not properly done

may result in serious risk to the safety

of the user. Any repairs must be

performed by qualified personnel.

With some problems, the display shows an

alarm code.

The majority of problems that can occur can

be solved without the need to contact an

Authorised Service Centre.

Problem and alarm code Possible cause and solution

You cannot activate the appli-

ance.

• Make sure that the mains plug is connected to the mains sock-

et.

• Make sure that there is no damaged fuse in the fuse box.

The program does not start. • Make sure that the appliance door is closed.

• If the delay start is set, cancel the setting or wait for the end of

the countdown.

• The appliance has started the procedure to recharge the resin

inside the water softener. The duration of the procedure is ap-

proximately 5 minutes.

The appliance does not fill with

water.

The display shows .

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low.

For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter in the inlet hose is not clogged.

• Make sure that the inlet hose has no kinks or bends.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZDT16020 FA in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zanussi ZDT16020 FA Manual

Product: