765943
29
Zoom out
Zoom in
Previous page
1/44
Next page
Regardless of the type of detergent used, set
the proper water hardness level to keep the
salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard water.
Regeneration process
For the correct water softener operation, the resin
of the softener device needs to be regenerated
regularly. This process is automatic and is the part
of the normal dishwasher operation.
When the prescribed quantity of water (see values
in the table) has been used since the previous
regeneration process, a new regeneration process
will be initiated between the final rinse and the
programme end.
Water softener level Amount of water (l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
In case of the high water softener setting, it may
occur also in the middle of the programme, before
the rinse (twice during a programme). Regeneration
initiation has no impact on the cycle duration,
unless it occurs in the middle of a programme or at
the end of a programme with a short drying phase.
In that cases, the regeneration prolongs the total
duration of a programme by additional 5 minutes.
Subsequently, the rinsing of the water softener that
lasts 5 minutes may begin in the same cycle or at
the beginning of the next programme. This activity
increases the total water consumption of a
programme by additional 4 litres and the total
energy consumption of a programme by additional
2 Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible more than
one in the same cycle) may prolong the programme
duration by another 5 minutes when it occurs at any
point at the beginning or in the middle of a
programme.
All the consumption values mentioned
in this section are determined in
accordance with the currently
applicable standard in laboratory
conditions with water hardness
2.5mmol/L according to the
2019/2022 regulation (water softener:
level 3).
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
How to set the water softener level
Make sure the appliance is in user mode.
1. Wait until the indicator starts to flash, the
indicator continues to flash and the
remaining indicators are off.
The intermittent flashing of the indicator shows
the current setting: e.g. 5 flashes + pause + 5
flashes = level 5.
2. Press the programme button repeatedly to
change the setting. Each pressing of the
programme button increases the level number.
After reaching the level 10, the count starts
again from the level 1.
3. Press the on/off button to confirm the setting.
THE RINSE AID EMPTY NOTIFICATION
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically released
during the hot rinse phase.
When the rinse aid chamber is empty, the rinse aid
indicator is turned on notifying to refill rinse aid. If
the drying results are satisfactory while using multi-
tablets only, it is possible to deactivate the
notification for refilling rinse aid. However, for best
drying performance, always use rinse aid.
If standard detergent or multi-tablets without rinse
aid are used, activate the notification to keep the
rinse aid refill indicator active.
How to deactivate the rinse aid empty
notification
Make sure the appliance is in user mode.
1. Press the programme button immediately.
The indicator starts to flash.
2. Wait until the indicator continues to flash
and the remaining programme indicators are
off.
29
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zanussi ZDLI1510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZDLI1510 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zanussi ZDLI1510

Zanussi ZDLI1510 User Manual - German, French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info