573473

Zanussi ZDH8333P Manual

25
Zoom out
Zoom in
Previous page
1/64
Next page
• Start a short programme (e.g. 30 minutes)
with moist laundry.
At the beginning of drying cycle (3-5
min.) there could be a slightly higher
sound level. It is because of start of
the compressor that is normal for
compressor powered appliances
such: refrigerators, freezers.
Daily Use
Start a programme without delay start
1. Prepare the laundry and load the appliance.
CAUTION!
Make sure that when you close
the door, the laundry does not
catch between the appliance
door and the rubber seal.
2. Press the on/off button to activate the
appliance.
3. Set the correct programme and options for
the type of load.
The display shows the programme duration.
4. Press the Start/Pause touchpad.
The programme starts.
Starting the programme with delay start
1. Set the correct programme and options for
the type of load.
2. Press the delay start button again and again
until the display shows the delay time you
want to set.
You can delay the start of a
programme from a minimum of
30 minutes to a maximum of 20
hours.
3. Press the Start/Pause touchpad.
The display shows the countdown of the delay
start.
When the countdown is completed, the
programme starts.
Change a programme
1. Press the on/off button to deactivate
appliance
2. Press the on/off button to activate the
appliance.
3. Set the programme.
Stand-by function
To decrease the energy consumption, this
function automatically deactivates the
appliance:
• After 5 minutes if you do not start the
programme.
• After 5 minutes from the end of the
programme.
At the end of the programme
When the programme is completed:
• An intermittent acoustic signal operates.
• The indicator flashes.
• The indicators Filter and Tank comes
on.
• The Start/Pause indicator is on.
The appliance continues to operate with the
crease guard phase for approximately other 30
minutes.
The crease guard phase removes creases from
your laundry.
You can remove the laundry before the crease
guard phase is completed. We recommend, for
better results, that you remove the laundry when
the phase is almost completed or completed.
When the crease guard phase is completed:
• The indicator is on but does not flash.
• The indicators Filter and Tank comes
on.
• Start/Pause indicator goes off.
1. Press the on/off button to deactivate the
appliance.
2. Open the appliance door.
3. Remove the laundry.
4. Close the appliance door.
Always clean the filter and empty the
water container when a programme
is completed.
www.zanussi.com 25
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zanussi ZDH8333P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZDH8333P in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 7,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info