626613
11
Zoom out
Zoom in
Previous page
1/52
Next page
Activate or deactivate the multitab function before
the start of a washing programme.
You cannot activate or deactivate the multitab function
when the programme operates. Cancel the washing pro-
gramme, then set the programme again.
To activate the multitab function:
Press and hold the two multitab buttons (function but-
tons D and E). The multitab indicator light comes on.
To deactivate the multitab function:
Press and hold the two multitab buttons (function but-
tons D and E). The multitab indicator light goes off.
Do these steps if the drying results are not satis-
factory:
1. Fill the rinse aid dispenser with rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position 2.
You can only activate or deactivate the rinse aid dis-
penser when the multitab function is activated.
To activate/deactivate the rinse aid dispenser:
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C.
The indicator lights for function buttons A, B,
and C start to flash.
4. Release function buttons B and C.
5. Press function button B.
The indicator lights for function buttons A and C
go off.
The indicator light for function button B contin-
ues to flash.
The digital display shows the setting.
Rinse aid dispenser deac-
tivated
Rinse aid dispenser activa-
ted
6. Press function button B again.
The digital display shows the new setting.
7. Switch off the appliance to save the operation.
To use normal detergent again:
1. Deactivate the multitab function.
2. Fill the salt container and rinse aid dispenser.
3. Adjust the water hardness setting to the highest level.
4. Do a washing programme without dishes.
5. Adjust the water softener to the water hardness in
your area.
6. Adjust the rinse aid dosage.
Setting and starting a washing programme
Set the washing programme with the door ajar.
The washing programme only starts after you
close the door. Until then it is possible to modify the set-
tings.
Do these steps to set and start a washing programme:
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press one of the programme buttons. Refer to the
chapter 'Washing programmes'.
The programme indicator light comes on.
All other programme indicator lights go off.
The digital display shows in flashing the pro-
gramme duration.
The programme-in-progress indicator light
comes on.
4. Close the door.
The washing programme starts automatically.
The programme-in-progress indicator light re-
mains on.
When the washing programme operates, you can-
not change the programme. Cancel the washing
programme.
You can select the washing programme and delay
start also with the door closed. When you press a
programme button you have only 3 seconds to select a
different washing programme or a delay start. After
these 3 seconds, the selected programme starts automat-
ically.
Warning! Only interrupt or cancel a washing
programme if necessary.
Caution! Open the door carefully. Hot steam can
come free.
11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zanussi ZDF4010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZDF4010 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 9,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zanussi ZDF4010

Zanussi ZDF4010 User Manual - German, Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info