669702
10
Zoom out
Zoom in
Previous page
1/40
Next page
CHARGING THE LIPO FLIGHT BATTERY
Connecting to the power source : the A10 Dual Balance Charger comes with built in
switching power supply. You can connect the AC power cord directly to the main AC
socket (110 to 240V AC).
NOTICE: While the A10 is connected to a
suitable 110 to 240V AC power source, the
combined power output for Channel A and
Channel B is 200W, capable of charging two
6-Cell (6S), 4,000mAh LiPo battery packs at
4.3A.
CONNECTING THE B
ATTERY
CHARGING
BATT/PROGRAM Select: Press INC and DEC to go through all the programs and press
START/ENTER to enter LiPo BATT Program (for flight BATT) or Li-ion BATT Program(for
proaction™).
Mode Select: Press INC and DEC to go through all the modes and press START/ENTER
to enter LiPo Balance Charge Mode (for aircraft’s flight battery), to enter Li-ion
Balance Charge Mode (for ProAction ground handle).
Battery Setting: Press START/ENTER, the current value will start to blink, press INC
and DEC to change the value and press START/ENTER to confirm your setting. For the
H920 Plus battery, it is recommended to set 4A (no more than 8A). For ProAction™
battery, it is recommended to set 2A (no more than 3A).
At the same time, the battery cells number will start blinking, press INC and DEC to
change the value and press START/ENTER to confirm your setting.
For the H920 Plus battery, 6S should be selected. For ProAction™, 4S should be
selected.
Program Start: Press and hold START/ENTER for 3 seconds to start the program.
The charger is detecting the battery cell.
NOTICE:
R shows the number of cells detected by the charger and S is the number of
cells set by you at the previous screen. If both numbers are not identical, press STOP
to go back to previous screen to recheck the number of cells of the battery pack
before going ahead. If both numbers are identical, press START/ENTER to start
charging process.
If the number of cells do not match after double checking the connection, please
contact technical support.
BUTTON DESCRIPTIONS
CH A / CH B: Used to switch from Channel A
to B or Channel B to A.
BATT PROG / STOP: Used to stop the
progress or go back to previous step/screen
DEC: Used to go through the menus and
decrease the parameter value.
INC: Used to go through the menus and
increase the parameter value.
ENTER / START: Used to enter parameter or
store parameter on screen.
9
9
AUFLADEN DES LIPO-FLUGAKKUS
An die Stromquelle anschließen: Der A10 Dual Balance Charger verfügt über ein Schaltnetzteil. Sie
können das Netzkabel direkt an die Steckdose anschließen (110 bis 240 V AC).
HINWEIS: Wenn das A10 an eine geeignete
110- bis 240-V-AC-Stromquelle angeschlossen
ist, beträgt die kombinierte Leistung für Kanal
A und Kanal B 200 W, womit zwei 6-zellige (6S)
4.000-mAh-LiPo-Akkupacks mit 4,3 A geladen
werden können.
DEN AKKU ANSCHLIESSEN
AUFLADEN
„BATT/PROGRAM“ auswählen: Drücken Sie „INC“ und „DEC“, um alle Programme durchzublättern,
und drücken Sie „START/ENTER“, um das Programm „LiPo BATT“ (für den Flugakku) oder das Pro-
gramm „Li-Ion BATT“ (für proaction™) aufzurufen.
Modus auswählen: Drücken Sie „INC“ und „DEC“, um alle Modi durchzublättern, und drücken Sie
„START/ENTER“, um den „LiPo Balance Charge Mode“ (für den Flugakku) oder den „Li-Ion Balance
Charge Mode“ (für die ProAction-Bodenstation) aufzurufen.
Akku einstellen: Drücken Sie „START/ENTER“, und der aktuelle Wert beginnt zu blinken. Drücken Sie
„INC“ und „DEC“, um den Wert zu ändern, und drücken Sie „START/ENTER“, um Ihre Einstellung zu
bestätigen. Für den Akku des H920 Plus werden 4 A empfohlen (nicht über 8 A). Für den Akku der
ProAction™ werden 2 A empfohlen (nicht über 3 A).
Gleichzeitig beginnt die Zahl für die Akkuzellen zu blinken. Drücken Sie „INC“ und „DEC“, um den
Wert zu ändern, und drücken Sie „START/ENTER“, um Ihre Einstellung zu bestätigen.
Für den Akku des H920 Plus muss 6S ausgewählt werden. Für ProAction™ muss 4S ausgewählt werden.
Programm starten: Drücken Sie 3 Sekunden lang auf „START/ENTER“, um das Programm zu starten.
Das Ladegerät erkennt nun die Akkuzelle.
HINWEIS: „R“ zeigt die Zahl der vom Ladegerät erkannten Zellen an, und „S“ ist die Anzahl der von
Ihnen im vorherigen Bildschirm eingestellten Anzahl von Zellen. Wenn die beiden Angaben nicht
übereinstimmen, drücken Sie „STOP“, um zum vorherigen Bildschirm zurückzukehren und die Anzahl
der Zellen zu überprüfen, bevor Sie fortfahren. Wenn beide Zahlen übereinstimmen, drücken Sie auf
„START/ENTER“, um den Ladevorgang zu starten.
Wenn die Angaben zur Zellenanzahl nach einer zweiten Überprüfung der Verbindung nicht überein-
stimmen, wenden Sie sich bitte an den technischen Support.
ERLÄUTERUNG DER TASTEN
CH A / CH B: Dient zum Umschalten von Kanal A zu
Kanal B oder von Kanal B zu Kanal A.
BATT PROG / STOP: Dient zum Anhalten des Vor-
gangs oder um zum vorherigen Bildschirm zurückzu-
gehen.
DEC: Dient zum Durchblättern der Menüs und zum
Vermindern eines Einstellwertes.
INC: Dient zum Durchblättern der Menüs und zum
Erhöhen eines Einstellwertes.
ENTER / START: Dient zum Eingeben eines Einstell-
wertes oder zum Speichern eines angezeigten Einstell-
wertes.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yuneec Tornado H920 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yuneec Tornado H920 Plus in the language / languages: German as an attachment in your email.

The manual is 3,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yuneec Tornado H920 Plus

Yuneec Tornado H920 Plus Quick start guide - English - 2 pages

Yuneec Tornado H920 Plus User Manual - English - 40 pages

Yuneec Tornado H920 Plus Quick start guide - German - 2 pages

Yuneec Tornado H920 Plus User Manual - French - 40 pages

Yuneec Tornado H920 Plus Quick start guide - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info