Manual Yuneec Tornado H920 Industry (page 13 of 39) (English)

669800

Zoom out

Zoom in

1/39

CHARGING THE LIPO FLIGHT BATTERY

Connecting to the power source : the A10 Dual Balance Charger comes with built in

switching power supply. You can connect the AC power cord directly to the main AC

socket (110 to 240V AC).

NOTICE: While the A10 is connected to a

suitable 110 to 240V AC power source, the

combined power output for Channel A and

Channel B is 200W, capable of charging two

6-Cell (6S), 4,000mAh LiPo battery packs at

4.3A.

CONNECTING THE BATTERY

CHARGING

BATT/PROGRAM Select: Press INC and DEC to go through all the programs and press

START/ENTER to enter LiPo BATT Program (for flight BATT) or Li-ion BATT Program(for

proaction™).

Mode Select: Press INC and DEC to go through all the modes and press START/ENTER

to enter LiPo Balance Charge Mode (for aircraft’s flight battery), to enter Li-ion

Balance Charge Mode (for ProAction ground handle).

Battery Setting: Press START/ENTER, the current value will start to blink, press INC

and DEC to change the value and press START/ENTER to confirm your setting. For the

TORNADO H920 battery, it is recommended to set 4A (no more than 8A). For

ProAction™ battery, it is recommended to set 2A (no more than 3A).

At the same time, the battery cells number will start blinking, press INC and DEC to

change the value and press START/ENTER to confirm your setting.

For the TORNADO H920 battery, 6S should be selected. For ProAction™, 4S should

be selected.

Program Start: Press and hold START/ENTER for 3 seconds to start the program.

The charger is detecting the battery cell.

NOTICE: R shows the number of cells detected by the charger and S is the number of

cells set by you at the previous screen. If both numbers are not identical, press STOP

to go back to previous screen to recheck the number of cells of the battery pack

before going ahead. If both numbers are identical, press START/ENTER to start

charging process.

If the number of cells do not match after double checking the connection, please

contact technical support.

ASSEMBLING THE H920

INSTALLING THE MOTOR ARMS

Fold the motor arms upwards and secure them using the straight knurled nut cover

located on the motor arms.

NOTICE: Don’t over tighten the straight knurled nuts, It may cause deformation of the arms.

INSTALLING THE PROPELLERS

Always ensure propellers are installed properly and with thread locker on the

fasteners. The rotors of the YUNEEC TORNADO H920 are made of high-strength

carbon fiber, the motors are extremely powerful, meaning that if the device is misused

there is a risk of material damage, serious injury and even fatal injury.

Mount the propellers on the motors and note the pointers ‘A’ and ‘B’ given on the

motor arms. This distinction between ‘A’ and ‘B’ refers to the rotation direction of the

motors. The rotation direction of the motors must match the rotation direction of the

propellers. Mount propeller ‘A’ on motor ‘A’ and propeller ‘B’ on motor ‘B’ and use the

screws with spring plate and 2mm Hexdriver enclosed to carefully screw in the propellers.

IMPORTANT NOTE: If the propellers are installed in the wrong places, it may cause

crash.

INSTALLING THE FLIGHT BATTERIES

After the flight batteries has been fully charged, they are ready to be installed in the

TORNADO H920:

STEP 1) Open the battery compartment flap with the status LED mounted on it by

carefully pulling the top edge of the flap.

STEP 2) Slide the batteries into the compartment with the EC3 blue, polarity-

protected connector leads / wires downward.

WARNING: The aircraft can take-off with 2 or 3 batteries. If utilizing 2 flight batteries,

make sure the 2 batteries are placed evenly within the two sides to balance the

aircraft. The voltage between each battery pack must be within 0.1V prior to

connecting the batteries to the aircraft. Be sure to use the included battery voltage meter.

STEP 3) Connect the flight battery to the relevant socket above the respective battery

on the H920 using the EC3 blue, polarity-protected connector.

NOTICE: The white socket is for battery charging, do not connect it to any port when

installing the batteries. If you do not install the battery in the correct orientation it will

not be possible to make a positive connection.

STEP 4) Fasten the battery belt, Close the battery door and ensure the door is closed

safely by the magnet.

INSTALLING THE MOTOR ARMS INSTALLING THE PROPELLERS INSTALLING THE FLIGHT BATTERIES

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yuneec Tornado H920 Industry in the language / languages: English as an attachment in your email.

The manual is 3,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yuneec Tornado H920 Industry Manual

Product: