663743
6
Zoom out
Zoom in
Previous page
1/86
Next page
6
BATTERY INSTALLATION
Turn the knob (10) of the battery compartment cover 90° counterclockwise to the
Open position and remove the battery container by raising it by its lug (see Fig. on the flyleaf).
Slide in four АА batteries so that the “+” and “-” match the polarity on the container.
Insert the battery container into its place and turn the knob 90° clockwise.
Battery charge level is shown in the status bar.
In case of complete battery discharge, red icon flashes in the status bar .
Warning! Remove the Battery pack from NV device during storage/transportation.
To prevent short circuit, carry the Battery Pack in a supplied pouch.
Note. Using the DNV Pulsar Battery Double Pack (#79176) you can significantly extend the self-
contained operating time of your riflescope.
7
Connect the external power supply to the USB port (8) of the riflescope.
Connect the second plug of the USB port to the Power Bank or PC.
The riflescope switches to operation from external power supply.
If the operates on external power supply, icon is shown. riflescope
Detailed description of powering from Power bank and PC is in section 13.
EXTERNAL POWER SUPPLY
The riflescope can be powered with an external power supply such as Power Bank (5V) or PC.
6
5
8
To ensure precise shooting, the riflescope should be correctly mounted on a rifle. Please follow these steps.
Install the mounting rings (bought separately) on the riflescope's tube and tighten the screws with the help of a
hex-nut wrench. If the eye relief is not sufficient, you can use mount Yukon SW-30 (#29048).
Install the riflescope on the rail of your rifle and make sure it is securely fixed.
The riflescope should be mounted as low as possible without touching either the barrel or the receiver.
Before tightening the mount rings make sure you have the necessary eye relief that allows you to see a full field of
view.
WARNING: if the riflescope does not have sufficient eye relief, its rearward motion may injure the shooter when
shooting.
MOUNTING RIFLESCOPE ON A RIFLE
Note. Please check that your sight is duly zeroed after changing mounting rings.
9
POWERING ON AND IMAGE SETUP
Open the lens cover (2).
Turn the unit on with a short press of the ON (4) button. Within a couple of seconds the display will light up.
To switch the display off, keep pressed the ON button for a second.
The display will go out, message “Display off” will appear.
To switch the display on, press briefly the ON button.
To switch the riflescope off, keep pressed the ON button for three seconds.
Message Display off and countdown from 3 to 1 appear on the screen, then the riflescope turns off.
To obtain a crisp image of the icons and the reticle on the display, rotate the dioptre adjustment ring (5).
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yukon Photon RT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yukon Photon RT in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info