813461
4
Zoom out
Zoom in
Previous page
1/28
Next page
4
2. Operating Instructions
WARNING! Do not operate the appliance if it is
damaged or has malfunctioned. If you suspect the
appliance is damaged or has malfunctioned call a
qualified service engineer to inspect the appliance,
and replace any part of the electrical system if
necessary, before reuse.
Do not disconnect the power at the mains supply whilst
the appliance is running. Use the functions on the
remote to turn the fire off and ensure the mains switch
has been moved to the off position before
disconnecting.
GENERAL
2.1 The appliance can be operated by the radio frequency
handset or the manual controls which are behind the plinth,
see Diagram 1.
NOTE: To use both remote and manual functions
the manual on/off switch must be in ‘ON’ position.
In order to prevent the product becoming too hot,
there is a 10s delay when turning on the heater
and a 10s delay when turning off the heater fan.
The manual button controls basic functions, not a
full range of controls. Use the remote hand set to
carry out all functions.
PREPARATION BEFORE USE
Batteries:
2.2 Ensure that the handset batteries are new and inserted
correctly.
2.3 Dispose of old batteries at an appropriate recycling facility.
LOCATION OF POWER SWITCH
2.4 The mains power switch is located on the control panel
located on the right-hand side, see Section 2a.
Mains Power
Switch
1
2.5 Switch ON (—) before operating either the remote or
manual controls.
2.6 A long beep is heard to indicate the fire is ready for use.
2a. Manual Control Panel
2a.1 The manual controls on appliance are located behind
the plinth on the right hand side of the appliance, see
Diagrams 1 & 2.
Mains Power
(On/Off) Switch
Fuel bed
setting button
Flame setting button
All Lights
On/ Off button
Reset Button for
Remote Control
Heater
Running
Indicators
2
2a.2 Turning on the appliance with the main power switch on ‘—‘
position. A long beep will be heard.
2a.3 Press “LIGHTS ON/OFF” to turn on or turn off both the
flame and fuel bed at the same time.
2a.4 There are 3 flame colour options:
Press “FLAME” button to select the colour of flame (3 kinds
of flame colour with flame) or return to the OFF position.
2a.5 Press “FUEL BED” button to select the colour of fuel bed
(14 kinds of fuel bed) or return to the OFF position.
Note: The appliance will lose the memory for the light
functions when the switch is set to the Off Position or
the remote runs out of power.
Heater Running Indicators (see Diagram 2)
2a.6 When the fan heater is used in conjunction with the flame or
fuel bed effects the heater running indicators will light up for
10 seconds.
The LEDs will illuminate for 10 seconds if the flame or fuel
bed effect is On.
If the fan heater is used independently, the heater running
indicators will stay on.
Reset Button for Remote Control
2a.7 If the handset loses signal or needs to be replaced then,
see Section 19 in Servicing Section for details.
User Instructions
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yeoman Exmoor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yeoman Exmoor in the language / languages: English as an attachment in your email.

The manual is 4.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info