799367
3
Zoom out
Zoom in
Previous page
1/4
Next page
www.yealink.com
Registering the Repeater
Registration
Note: You cannot set the base station in registration mode, if there are 5 handsets
registered on the base station.
1. Plug the repeater into a AC outlet.
Power LED is green and DECT LED is slowly flashing red.
3. Set base station in registration mode (Long press paging key on the base
station till the first LED flashes).
If base station is found, DECT LED will fast flash green.
When DECT LED is on, registration to base station is successful
(green: good DECT link).
Incoming call:
The Relay LED on repeater is green.
The Relay LED on repeater is green till call is finished.
The Relay LED on repeater is green till call is finished.
Relay Connection
Outgoing call:
1. Place a call to the handset in repeater zone.
2. Accept the call.
1. Place a call using the handset in repeater zone.
De-registration
1. Plug the repeater into a AC outlet.
If you want to register the repeater to another base station, de-register the
repeater beforehand as described below:
If the repeater is registered to a base station, DECT LED is green.
2. Long press the reset key on the repeater.
DECT LED is slow flashing red after successful de-registering the
repeater, and the repeater is ready for a new registration.
LED Status
The DECT repeater has three LED indicators describing the repeater
statuses. The following table provides instructions on repeater statuses and
LED indications.
DECT Repeater RT20U User Guide
52
RelayStatus Power DECT
Power On
Not registered, auto
search base station
Base station found
Registered to base
station, ready for use
Active relay
Registered, but not
linked to base station
Green
Green
Green
Green
Green
Green Alternately fast green
– once red Flashing
Fast flashing green
Slow flashing red
Off
Green
Green
Off
Off
Off
Off
Green
Off
The DECT LED can indicate the DECT link quality. RT20U must be operated
with this LED in green status. The following table provides instructions on
DECT link quality and LED color.
Medium
Poor
Yellow
Red
DECT link Color
Excellent to good Green
Registration cannot be performed if the repeater is already registered to one
base station. In this case, de-register the repeater before attempting
registration. For more information, refer to “De-registration”.
2. Enable the repeater mode on the handset at the path: Settings->
System Settings->Repeater Mode.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yealink RT20U - DECT Repeater at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yealink RT20U - DECT Repeater in the language / languages: English as an attachment in your email.

The manual is 0.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info