734892
18
Zoom out
Zoom in
Previous page
1/31
Next page
18
WARNING The high pressure stream of water that this
pressure washer produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER repair leaking connections with sealant of any
kind. replace o-ring or seal.
ENGINE MAINTENANCE
WARNING Unintentional sparking could cause re or
electric shock resulting in death or
serious injury.
WHEN ADJUSTING OR MAKING REPAIRSTOYOUR
PRESSUREWASHER
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DONOT check for spark with spark plug removed.
Oil
Oil Recommendations
We recommend the use of CRAFTSMAN Warranty Certied
oils for best performance. Other high-quality detergent oils
are acceptable if classified for service SF, SG, SH, SJ or
higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard
starting.
* Above 80°F (27°C) the use of 10W30 may cause
increased oil consumption. Check oil level more
frequently.
Checking Oil Level.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean cloth.
Replace and tighten dipstick. Remove and check oil
level.
3. Verify oil is at FULL mark (top hole) on dipstick. Replace
and tighten dipstick.
Adding Oil.
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in Checking O Level.
3. If needed, slowly pour oil into oil ll opening to the FULL
mark (top hole) on dipstick. DO NOT overll.
NOTICE
Oil level should be checked prior to each use or at
least every 5 hours of operation. Keep oil level
maintained.
Overfilling with oil could cause the engine to not start, or
hard starting.
• DO NOT overll.
• If over the FULL mark on dipstick, drain oil to reduce oil
level to FULL mark on dipstick.
Changing Oil
If you are using your pressure washer under extremely dirty
or dusty conditions, or in extremely hot weather, change oil
more often.
CAUTION Avoid prolonged or repeated skin contact
with used motor oil.
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
• Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Change oil while engine is still warm from running, as
follows:
1. Drain fuel tank by running pressure washer until fuel tank
is empty.
2. Disconnect spark plug wire and keep it away from the
spark plug.
3. Clean area around oil fill, remove oil fill cap/dipstick.
Wipe dipstick clean.
4. Tip your pressure washer to drain oil from the oil ll into
a suitable container making sure you tip your unit away
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yardforce Y0GWC3200R0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce Y0GWC3200R0 in the language / languages: English as an attachment in your email.

The manual is 7,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info