Manual Yardforce SC600 ECO (page 15 of 49) (English, German)

733742

Zoom out

Zoom in

1/49

26 27

INSTALLATION GUIDEINSTALLATION GUIDE

Lightning protection

In order to prevent lightning cause damage to the machine, please don't place charging

station under the tall trees.

4.4. Pegging Out the Boundary Wire

Next step is to fix the boundary wire, so locate the boundary wire (item 19), unpack it

and locate the free end. Also locate the xing pegs (item 15) and lay each one on Lawn

at approximately the correct distance from lawn edges (40cm) and obstacles. There is a

gauge supplied for this (item 17) (Remember to ensure the lawn grass height is maximum

of 60mm tall, if not cut it before you start pegging). The boundary wire will be laid on top

of the grass there is absolutely no need to dig into the ground. The closer you can lay

this boundary wire to the ground level, the safer it will be with no risk of tripping or cutter

damage. In a very short time the wire will covered by grass and as the voltage in this wire

is only 32V. It is totally safe to human beings and pets.

The peg should be knocked into lawn

with wire location to boundary outside

like shown.

Cutting

area

40 cm

80 cm

It is recommended to place the pegs at a distance of 80 cm apart approximately, but these

can be closer where tight bends are required for accurate cutting, do not x your pegs

permanently when laying out for rst time, it is advisable to only partially knock in the pegs

with a hammer and ensure the wire location slots are all in same orientation to the outside

of boundary.

Once all are in correct position, then the boundary wire can be threaded into the slots on

pegs one by one around the working area edge. Please start from the charging station

and allow an additional 1m of spare wire before cutting off the wire in case a peg needs

moving later. When laying out the wire, and adding the pegs, be sure not to tighten the

boundary too hard to prevent wire get damaged. Also remember there should be a 2 to

4 meter straight length of wire in front of the charging station in order to allow the robot

successfully to dock into charging station. Please be careful also when installing this wire

to prevent kinks etc.

Note! If there are hard surfaces where these pegs cannot be used such as a

concrete or garden tiles etc. then a screw and plug may be required. If a screw is

used then there must be an insulation washer applied.

If the boundary wire needs to be joined for, only use the connectors provided by

manufacturer (Item18).

See below for some further sketches giving more distance guidelines.

The potential location of charging station

The end point of boundary

1 m extra wire

for potential

adjustment

The initial point of

boundary

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce SC600 ECO in the language / languages: English, German as an attachment in your email.

The manual is 10,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yardforce SC600 ECO Manual

Product: