・Is the optimizer microphone firmly connected to this unit?
・Is the optimizer microphone placed in a proper loacation?
・Are there any large obstacles in between the optimizer microphone and the
walls in your listening room?
・The AUTO SETUP procedure starts in 10 seconds after pressing ENTER
on step 7. To achieve the best results possible, evacuate yourself for your
listening room until the AUTO SETUP procedure is completed.
・To cancel the AUTO SETUP procedure after it is started, press RETURN.
・The AUTO SETUP procedure takes about 3 minutes.
Press ENTER to start the AUTO SETUP procedure.
The following screen appears on the TV and the AUTO SETUP procedure
starts in 10 seconds.
The setup screen automatically changes during the AUTO SETUP
procedure.
If any error occurs, the corresponding error message appears on the screen.
In this case, see “Error messages for AUTO SETUP” on page 33 in the
Owner’s Manual and then follow the instructions. To start the AUTO SETUP
procedure once again, press RETURN and then carry out the procedure from
step 5.
When the AUTO SETUP procedure is complete, the following screen
appears on the TV.
*
This is an example of the result screen.
The result may differ depending on the
environment.
Press ENTER.
The result is confirmed and the following screen appears on the TV for 2
seconds and then the menu screen disappears from the TV.
The new settings are automatically saved in the system memory.
Disconnect the optimizer microphone and keep it in a safe place.
Enjoy TV or DVD audio in surround sound.
For instructions on your TV or DVD player, refer to the owner’s manual supplied with each component.
Before carrying out the procedure below, set the volume of this unit to 30. If necessary, adjust the volume level in
step 4.
Enjoying surround sound
Carry out the AUTO SETUP (IntelliBeam) procedure to adjust the settings that
best match your listening environment.
This unit employs the YAMAHA IntelliBeam technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments
that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are
no children around in the listening room while the AUTO SETUP procedure is in progress.
Press STANDBY/ON on
the remote control.
The power of this unit turns on.
If a subwoofer with adjustable volume and
crossover/high cut frequency controls is
connected to this unit, set the volume
between 10 and 12 o’clock as viewed on
a conventional clockface and set the
crossover/high cut frequency to the
maximum.
Turn on the power of your TV.
Select the appropriate video input
on your TV.
Set the operation mode selector to YSP.
Press and hold AUTO SETUP for more than 2
seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the video pin cable (connection
3 in the diagram on the front page) is connected properly and then press
YSP followed by MENU.
If you hear sound output from your TV speakers, turn down the volume level
until you cannot hear any sound.
Use the remote control supplied with your TV.
Press VOLUME +/– on the remote control to adjust
the volume level of this unit.
Press one of the beam mode buttons on the
remote control to select the desired beam mode.
Select one of the three beam modes that best matches the current input source of
this unit.
For further information on the beam modes, see page 40 in the Owner’s Manual.
To fine-tune the listening environment parameters manually or make advanced settings for
speaker positions, sound beams, etc., see “MANUAL SETUP” on page 57 in the Owner’s Manual.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Yamaha YSP-900 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Yamaha YSP-900 in the language / languages: German as an attachment in your email.
The manual is 2,36 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
