516955
25
Zoom out
Zoom in
Previous page
1/82
Next page
Initial settings
25 En
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
APPENDIX
The screen below is displayed after connecting
IntelliBeam microphone to the unit.
1)
4
Press the ENTER key to start the AUTO
SETUP procedure and then leave the room
within 10 seconds.
2)
The screen automatically changes during the AUTO
SETUP procedure.
If the AUTO SETUP procedure is complete, this unit
rings the chimes.
3)
AUTO SETUP
(PREPARATION & CHECK)
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from Sound Pro-
jector. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
Follow the instructions below and then leave the room. If you remain
in the room, you may obstruct the beam, or the microphone may pick
up any sounds you make, possibly resulting in improper
configuration of settings.
Note
ENVIRONMENT CHECK: Success
BEAM MODE: 5Beam/Plus2
SHOW RESULT
MESUREMENT COMPLETE.
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
Will begin in 10 sec.
Please leave the room
----------
AUTO SETUP START
[RETURN]:Cancel
(After 3 min.)
5
Press the ENTER key to confirm the
results.
4)
Measurement results are applied to this unit.
The measurement results are stored in the internal
memory of this unit until you run the AUTO SETUP
procedure again or configure the settings manually.
You can save the several measurement results pressing
the SYSTEM MEMORY key (p. 28).
6
Remove the IntelliBeam microphone.
The “AUTO SETUP COMPLETE” screen closes.
5)
Keep the IntelliBeam microphone in a safe place.
AUTO SETUP COMPLETE
Please remove the MIC
from Sound Projector
and the listening position.
Press [SYSTEM MEMORY] key
to save set-up in the memory.
“BEAM+SOUND OPTIMIZE” is selected automatically. When you
perform “BEAM OPTIMIZE ONLY” or “SOUND OPTIMIZE ONLY
only, refer to “AUTO SETUP via setup menu” (p. 26).
Wait outside the room during the AUTO SETUP procedure.
Remaining in the room after the AUTO SETUP process begins may
result in the improper configuration of settings as your body may
obstruct sound beams or the microphone may pick up sounds you
make inadvertently.
The AUTO SETUP procedure takes about 3 minutes.
To cancel the AUTO SETUP procedure after it is started, press the
RETURN key.
If an error occurs, an error buzzer sounds and an error message is
displayed. For details on error messages, see “If an error message is
displayed” (p. 27).
If “ENVIRONMENT CHECK:Failure” is displayed, accurate
measurement may not have been possible. See “ERROR-E1” under
“Error messages” (p. 27) for the remedy to this most common error.
Press the RETURN key and begin measurement again.
Depending on the environment of your listening room, the front left
and right beam angles and left and right surround beam angles may be
set to the same value even if “BEAM MODE :5Beam” is displayed as
a result.
If you do not want to apply the results, press RETURN key.
When AUTO SETUP is performed from the setup menu, the menu
selection screen of the setup menu appears.
1) y
2) y
3) y
4) y
5) y
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha YSP-4300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha YSP-4300 in the language / languages: English as an attachment in your email.

The manual is 4,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha YSP-4300

Yamaha YSP-4300 Quick start guide - English - 116 pages

Yamaha YSP-4300 User Manual - English - 35 pages

Yamaha YSP-4300 User Manual - German - 82 pages

Yamaha YSP-4300 Quick start guide - German - 2 pages

Yamaha YSP-4300 User Manual - German - 35 pages

Yamaha YSP-4300 Quick start guide - Dutch - 2 pages

Yamaha YSP-4300 User Manual - Dutch - 35 pages

Yamaha YSP-4300 User Manual - Dutch - 82 pages

Yamaha YSP-4300 User Manual - French - 2 pages

Yamaha YSP-4300 User Manual - French - 82 pages

Yamaha YSP-4300 User Manual - French - 35 pages

Yamaha YSP-4300 User Manual - Italian - 82 pages

Yamaha YSP-4300 User Manual - Italian - 35 pages

Yamaha YSP-4300 User Manual - Swedish - 82 pages

Yamaha YSP-4300 User Manual - Swedish - 35 pages

Yamaha YSP-4300 User Manual - Spanish - 82 pages

Yamaha YSP-4300 User Manual - Spanish - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info