•Initializing this unit also initializes measurement results for IntelliBeam and settings stored in system memory. Perform “AUTO SETUP” from the “IntelliBeam” menu again.
MenuSettings/Adjustable rangeDescription
TURN ON VOLUMEOFF (Not set) (default), 1 to 70
Set the initial volume level when the power of this unit is turned on.
When set to “OFF”, volume level is the same as when this unit is turned off.
MAX VOLUME1 to 99, MAX (Maximum) (default)
Set the maximum volume level so that this unit will not output sound beyond the
limited volume level.
INPUT LOCK
ON (INPUT key operation is disabled)
OFF (INPUT key operation is enabled) (default)
Select whether or not to enable the INPUT key on the center unit.
PANEL LOCK
ON (Key operation on the center unit is disabled)
OFF (Key operation on the center unit is enabled) (default)
Select whether or not to enable key operations on the center unit (except the
advanced setup operations).
IR INPUT POWER
ON (Enables power-on)
OFF (Disables power-on) (default)
Select whether or not to automatically turn on this unit by pressing an input selector
key on the remote control when the unit is turned off.
AC ON STANDBY
ON (Enters standby mode) (default)
OFF (Restores the state before power was lost)
Set this unit’s power to off when the AC power is recovered after the power to this
unit was lost temporally (disconnect the AC power plug from the wall outlet, power
outage, etc.).
MEMORY PROTECT
ON (Protect is performed)
OFF (Protect is not performed) (default)
Protect the settings you have saved in the system memory.
YRB FL
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the front left channel. Refer to page 73
for details of YRB-100.
YRB FR
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the front right channel. Refer to page 73
for details of YRB-100.
YRB SL
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the surround left channel. Refer to page
73 for details of YRB-100.
YRB SR
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the surround right channel. Refer to
page 73 for details of YRB-100.
AUTO POWER STANDBY
ON (This unit turns off automatically) (default setting for U.K., Europe and Russia
models)
OFF (This unit does not turn off automatically) (default setting other than U.K.,
Europe and Russia models)
When set to “ON”, this unit turns off automatically in any of the following situations:
•Audio is coming from the selected input source. However, no operations have
been performed for 8 hours or more.
•Bluetooth is selected as the playback device. However, no audio has come out
from the device or no operation has been performed for 20 minutes or more.
•HDMI 1, 2, or 3 is selected as the playback device. However, the playback
device has been disconnected from the selected HDMI IN jack for 20 minutes or
more.
FW UPDATE
02.00.04 (The firmware version is displayed)
START OK? (Firmware is updated)
Confirm firmware version/update firmware.
INITIALIZE
OK (All settings are restored to their default values)
CANCEL (Settings are not restored to their default values) (default)
Reset all of the parameters of this unit to the factory presets. When the unit freezed,
the problem may solve by restoring to their default values.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Yamaha YSP-2500 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Yamaha YSP-2500 in the language / languages: English as an attachment in your email.
The manual is 5,59 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
