600318
20
Zoom out
Zoom in
Previous page
1/30
Next page
Keyboard Stand Assembly
Be careful not to confuse parts, and be sure to install all parts in the
correct direction. Please assemble in accordance with the se-
quence given below.
Assembly should be carried out by at least two persons.
Be sure to use the correct screw size, as indicated above. Use of
incorrect screws can cause damage.
Be sure to tighten up all screws upon completing assembly of each
unit.
To disassemble, reverse the assembly sequence given below.
ZOpen the box and remove all the parts.
On opening the box you should find the parts shown in
the illustration above. Check to make sure that all the
required parts are provided.
XUntie the two vinyl ties.
Untie both vinyl ties and straighten out the bundled cord
attached to the bottom of the pedal box. Use the vinyl tie
attached to the bottom of the pedal box to secure the cord.
Don’t discard the other vinyl tie, you’ll need it later in
step N.
CAttach the side panels (D) to the pedal box
(C).
Place the pedal box on top of the wooden blocks attached
to the side panels (D), and while eliminating any gaps
between the pedal box and side panels, attach using the
four 6 x 35 millimeter round-head screws 1 — two
screws on each side. Make sure the pedals extend in the
same direction as the side panel feet.
1
Zusammenbau und Aufstellung
Achten Sie darauf, die Teile nicht zu verwechseln, und installieren
Sie alle Teile in der richtigen Ausrichtung. Gehen Sie beim
Zusammenbau bitte in der angegebenen Reihenfolge vor.
Die Montage sollte von mindestens zwei Personen vorgenommen
werden.
Achten Sie darauf, die richtige Schraubengröße zu verwenden, wie
es oben gezeigt ist. Die Verwendung der falschen Schrauben kann
zu Schäden führen.
Achten Sie während der Montage darauf, bei jedem Arbeitsgang
alle Schrauben festzuziehen.
Für die Demontage muß die angegebene Reihenfolge umgekehrt
befolgt werden.
ZÖffnen Sie den Karton und nehmen Sie alle
Teile heraus.
Im Karton sollten die oben abgebildeten Teile enthalten
sein. Prüfen Sie zunächst bitte, ob alle Teile vollständig
vorhanden sind.
XLösen Sie die beiden Kabelbinder.
Lösen Sie die beiden Kabelbinder, um das unten am
Pedalkasten angebrachte Kabel dann bis zur vollen Länge
zu ziehen. Sichern Sie das Kabel mit dem Kabelbinder an
der Unterseite des Pedalkastens. Werfen Sie den anderen
Kabelbinder nicht weg — er wird in Schritt N wieder
gebraucht.
CBefestigen Sie die Seitenwände (D) am
Pedalkasten (C).
Stellen Sie den Pedalkasten auf die Holzblöcke an den
Seitenwänden (D), um ihn dann mit vier 6 x 35 mm Halb-
rundschrauben 1 (jeweils zwei Schrauben links und
rechts) so an den Seitenwänden festzuschrauben, daß kein
Zwischenraum verbleibt. Achten Sie dabei darauf, daß die
Pedale in dieselbe Richtung weisen wie die vor-
springenden Teile der Füße.
Bundled pedal cord inside
Gebündeltes Pedalkabel
Cordon de pédalier enroulé à lintérieur
Cable de pedales enrollado en el interior
6 x 35 mm round-head screws x 4 1
6 x 35 mm Halbrundschrauben x 4 1
Vis à tête ronde de 6 x 35 mm x 4 1
Tornillos de cabeza redonda
de 6 x 35 mm x 4 1
4 x 10 mm round-head screws x 2 2
4 x 10 mm Halbrundschrauben x 2 2
Vis à tête ronde de 4 x 10 mm x 2 2
Tornillos de cabeza redonda
de 4 x 10 mm x 2 2
4 x 20 mm tapping screws x 4 3
4 x 20 mm Schneidschrauben x 4 3
Vis auto-taraudeuses 4 x 20 mm x 4 3
Tornillos de autoenrosque
de 4 x 20 mm x 4 3
6 x 16 mm flat-head screws x 4 4
6 x 16 mm Senkschrauben x 4 4
Vis à tête plate de 6 x 16 mm x 4 4
Tornillos de cabeza plana
de 6 x 16 mm x 4 4
A
B
C
D
D
18
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha YDP-88II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha YDP-88II in the language / languages: German as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha YDP-88II

Yamaha YDP-88II User Manual - English - 30 pages

Yamaha YDP-88II User Manual - French - 30 pages

Yamaha YDP-88II User Manual - Spanish - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info