689860

Yamaha XV750 Virago Manual

339
Zoom out
Zoom in
Previous page
1/363
Next page
8B-18
Chapter 8 Part B Electrical system (XV700-1100 models)
30.7 Starter clutch details (XV1000, XV1100 and 1986 and later
XV700 and XV750 models)
1 Starter clutch 10 Drive lever shaft
2 Snap-ring 11 Oil seal
3 Shaft 12 Collar
4 Starter wheel - 13 Screw
5 Inner idler gear 14 Drive lever
6 Outer idler gear 15 return spring
7 Thrust collar 16 Pivot bolt
8 Spring 17 Gasket
9 Collar 18 Nut
30.10a Remove the solenoid screws and nuts .,
30.10b ... then remove the cover and remove the solenoid
7 Remove the thrust collar (see illustration). Remove the O-ring,
shaft, starter wheel, spring, outer idler gear, inner idler gear and
remaining thrust collar.
8 Remove the snap-ring, starter clutch and remaining snap-ring.
9 Remove the drive lever collar screw (see illustration 30.6).
10 Remove the two solenoid securing nuts. Remove the solenoid
screws, pull the solenoid out and remove the gasket (see
illustrations).
11 Remove the drive lever pivot bolt, then remove the drive lever,
collar and spring (see illustration).
Inspection
Refer to illustrations 30.12a, 30.12b, 30.13a, 31,13b and 30.13c
12 If you're working on a 1981 through 1985 XV700, XV750 or XV920
model, clean the starter clutch components and check them for wear
and damage (see illustration). Replace any worn or damaged parts.
Place the spring clips in position and try to rotate them. If the turn
easily, replace them. If you're in doubt about their condition, pull on
them with a spring scale and measure the force required to rotate them
(see illustration). If it's less than the value listed in this Chapter's
Specifications, replace them.
13 If you're working on a 1986 or later XV700 or XV750, an XV1000
or an XV1100 model, clean the drive assembly components and check
30.11 Remove the pivot and starter drive lever
… 339 …


Need help? Post your question in this forum.

Forumrules
1

Forum

yamaha-xv750-virago

Reset search

  • Hi am Gavin from Napier, New Zealand- Does anyone know the correct clearance between the clutch basket bush and the gearbox input shaft on my 1990 Yamaha Virago xv 750 please? Submitted on 12-12-2021 at 00:03

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha XV750 Virago at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha XV750 Virago in the language / languages: English as an attachment in your email.

The manual is 52,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info