689860

Yamaha XV750 Virago Manual

311
Zoom out
Zoom in
Previous page
1/363
Next page
8A-8
Chapter 8 Part A Electrical system (XV535 models)
13.2 ... and from the drive unit on the left
fork leg
13.4 Remove the speedometer mounting
nuts...
13.5 ... and the mounting screws, then
detach the speedometer from the housing I
2 Note how it's routed, then unscrew the speedometer cable from
the drive gear at the left front fork (see illustration).
Speedometer removal
Refer to illustrations 13.4 and 13.5
3 Disconnect the cable from the speedometer (see illustration
13.1).
4 Remove the Allen bolts and washers and detach the speedometer
housing bracket (see illustration).
5 Lift the speedometer away from the bracket and turn it over.
Remove the self-tapping screw and detach the speedometer from the
housing (see illustration). Follow the speedometer wiring harness to
its connector (inside a rubber cover below the speedometer) and
disconnect it.
Installation
6 Installation is the reverse of the removal procedure. Be sure the
speedometer cable and wiring harness are routed so it doesn't cause
the steering to bind or interfere with other components. The squared-
off ends of the cable must fit into their spindles in the speedometer and
drive gear.
14 Instrument and warning light bulbs - replacement
Warning light bulbs
Refer to illustrations 14.1 and 14.3
1 The warning light bulbs are beneath a cover located behind and
beneath the handlebar (see illustration).
2 For access to the bulbs, remove the handlebar (see Chapter 5).
The cables, wiring and brake hoses can be left attached; just support
the handlebar so no components are strained.
3 Remove the screws and lift off the cover (see illustration).
Pull the bulb out and install a new one.
4 Install the cover and the handlebar. Tighten the handlebar
fasteners to the torque listed in the Chapter 5 Specifications.
Speedometer light bulb
Refer to illustrations 14.6a and 14.6b
5 Remove the speedometer from the housing (see Section 13).
6 Pull the rubber socket out of the back of the speedometer (see
illustration), then pull the bulb out of the socket (see illustration). If
the socket contacts are dirty or corroded, they should be scraped
clean and sprayed with electrical contact cleaner before new bulbs are
installed.
7 Carefully push the new bulb into position, then push the socket
into the speedometer.
14.1 The warning lights are contained in this housing
14.3 With the handlebar removed, remove the cover screws
(arrows), lift off the cover and pull the bulb out of the socket
… 311 …


Need help? Post your question in this forum.

Forumrules
1

Forum

yamaha-xv750-virago

Reset search

  • Hi am Gavin from Napier, New Zealand- Does anyone know the correct clearance between the clutch basket bush and the gearbox input shaft on my 1990 Yamaha Virago xv 750 please? Submitted on 12-12-2021 at 00:03

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha XV750 Virago at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha XV750 Virago in the language / languages: English as an attachment in your email.

The manual is 52,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info