514325
225
Zoom out
Zoom in
Previous page
1/232
Next page
7-16
THROTTLE POSITION SENSOR SYSTEM
HANDLING NOTE
Do not loosen the screw (throttle
position sensor) "1" except when
changing the throttle position sen-
sor due to failure because it will
cause a drop in engine perfor-
mance.
CHECKING THE COUPLERS AND
LEADS CONNECTION
1. Check:
Couplers and leads connection
Rust/dust/looseness/short-circuit
Repair or replace.
CHECKING THE THROTTLE
POSITION SENSOR COIL
1. Inspect:
Throttle position sensor coil resis-
tance
Out of specification Replace.
2. Loosen:
Throttle stop screw "1"
Turn out the throttle stop screw until
the throttle shaft is in the full close po-
sition.
3. Inspect:
Throttle position sensor coil vari-
able resistance
Check that the resistance in in-
creased as the throttle grip is
moved from the full close position
to the full open position.
Out of specification Replace.
CHANGING AND ADJUSTING THE
THROTTLE POSITION SENSOR
1. Remove:
Throttle position sensor coupler
Carburetor
2. Remove:
Screw (throttle position sensor)
"1"
Throttle position sensor "2"
Loosen the screw (throttle position
sensor) using the T25 bit.
3. Replace:
Throttle position sensor
4. Install:
Throttle position sensor "1"
Screw (throttle position sensor)
"2"
Align the slot "a" in the throttle posi-
tion sensor with the projection "b"
on the carburetor.
Temporarily tighten the screw
(throttle position sensor).
5. Install:
•Carburetor
Throttle position sensor coupler
6. Adjust:
Engine idling speed
Refer to "ADJUSTING THE EN-
GINE IDLING SPEED" section in
the CHAPTER 3.
7. Insert the thin electric conductors
"2" (lead) into the throttle position
sensor coupler "1", as shown, and
connect the tester to them.
Do not insert the electric conduc-
tors more than required because
it may reduce the waterproof
function of the coupler.
Make sure that a short-circuit
does not develop between the
terminals because it may cause
damage to electrical compo-
nents.
8. Start the engine.
Tester (+) lead Blue lead "1"
Tester (-) lead Black lead "2"
Throttle po-
sition sen-
sor coil
resistance
Tester se-
lector posi-
tion
4–6 kΩ at
20°C (68 °F)
kΩ×1
Tester (+) lead Yellow lead "1"
Tester (-) lead Black lead "2"
Throttle posi-
tion sensor coil
variable resis-
tance
Tester
selec-
tor po-
sition
Full
closed
Full
opene
d
kΩ×1
Zero –3
kΩat
20°C
(68 °F)
4–6
kΩat
20 °C
(68 °F)
Tester (+) lead Yellow lead "3"
Tester (-) lead Black lead "4"
225


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha WR 250 - 2013 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha WR 250 - 2013 in the language / languages: English as an attachment in your email.

The manual is 14,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha WR 250 - 2013

Yamaha WR 250 - 2013 User Manual - German - 238 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info