559139
11
Zoom out
Zoom in
Previous page
1/72
Next page
English
E-9
Cause
The AC adaptor is not properly plugged into
the AC receptacle.
The power of the amplifier unit is set in the
standby mode.
Connections are faulty or incomplete.
The appropriate input mode is not selected.
The volume setting is low.
The MUTE function is active. (The indicator
on the left side of the MUTE button is lit.)
The SURROUND level control is set to
minimum.
The surround mode is off.
The CENTER level control is set to minimum.
The SPEAKER MODE switch on the rear
panel of the amplifier unit is set to “2CH” or
“4CH”.
The surround mode is off.
Dim illumination of an indicator means that
signals encoded with the corresponding
format (DTS or Dolby Digital) is inputted to
this system. In this case, the signals are
mixed into 2 channels and reproduced from
the front speakers only.
A Dolby Digital 2-channel encoded source is
inputted to this system.
The level of the input signal is too high.
The level of the input signal is too low.
Connections are faulty or incomplete.
The amplifier unit is too close to the monitor.
Problem
No sound from the speakers or
subwoofer.
No sound from the surround speakers
No sound from the center speaker
No sound from the center and
surround speakers though the DTS or
DIGITAL mode indicator is dimly
illuminated.
Though a Dolby Digital encoded
source is inputted to this system, the
DIGITAL mode indicator is dimly
illuminated and the
PROLOGIC
mode indicator is brightly illuminated.
Sound is distorted.
Noise.
What to Do
Insert the AC adaptor firmly into the AC
receptacle.
Turn on the power by pressing the power
switch. (The power indicator lights up.)
Make the connections again.
Select the appropriate input mode by
pressing the INPUT selector button.
Turn the MASTER VOLUME control
clockwise to increase the volume.
Press the MUTE button to cancel this
function.
Turn the SURROUND level control clockwise
to increase the level.
Select the appropriate surround mode by
pressing the MODE button. If no mode can
be selected, change the input source to
another which is encoded with DTS, Dolby
Digital or Dolby Prologic.
Turn the CENTER level control clockwise to
increase the level.
Set the SPEAKER MODE switch to “5CH”.
Select the appropriate surround mode by
pressing the MODE button. If no mode can
be selected, change the input source to
another which is encoded with DTS, Dolby
Digital or Dolby Prologic.
Press the MODE button for the appropriate
surround format. The indicator turns bright,
and the center and surround speakers
reproduce sounds since the surround format
is decoded.
If the input source is compatible with 5.1
channels, select “5.1-channel mode” on the
player which is sending signals to this
system. (If the input source is not compatible
with 5.1 channels, you can enjoy the source
in a multi-channel mode by using the
PROLOGIC surround mode.)
Turn down the output level on the connected
component.
Turn up the output level on the connected
component.
Make the connections again.
Place the amplifier unit away from the
monitor.
Refer to the chart below if this system does not function properly. If the problem you are experiencing is not listed below or if
the instructions given below do not help, disconnect the AC adaptor and contact your authorized YAMAHA dealer or service
center.
Troubleshooting
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha TSS-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha TSS-1 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info