559127
64
Zoom out
Zoom in
Previous page
1/68
Next page
62
Problem
No sound from the rear
center speaker.
A “humming” sound can
be heard.
The volume level is low
while playing a record.
The volume level cannot
be increased, or the
sound is distorted.
The sound effect cannot
be recorded.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack of
this unit.
The sound field
parameters and some
other settings on the
unit cannot be changed.
The unit does not
operate properly.
“CHECK SP WIRES”
appears on the front
panel display.
There is noise interfer-
ence from digital or
high-frequency
equipment, or this unit.
The unit suddenly turns
into standby mode.
Cause
“SOUND 1C REAR LR” or “SOUND 1D
REAR CT” on the set menu is set to NON.
The Dolby Digital EX or the DTS-ES
decoder is not switched on.
Incorrect cable connections.
No connection from the turntable to the
GND terminal.
The record is being played on a turntable
with an MC cartridge.
The component connected to the OUT
(REC) jacks of this unit is turned off.
It is not possible to record the sound effect
with a recording component.
There is no source component connected
to the DIGITAL INPUT jacks of this unit.
“OPTION 2 MEM. GUARD” in the set
menu is set to ON.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
The speaker cables are short circuited.
This unit is too close to the digital or high-
frequency equipment.
The internal temperature has become too
high and the overheat protection circuitry
has been activated.
Remedy
Select LRG or SML.
Press 6.1/5.1 on the remote control to switch the
decoder on.
Firmly connect the audio plugs. If the problem
persists, the cables may be defective.
Connect the grounding cord of your turntable to
the GND terminal of this unit.
The turntable should be connected to this unit
through an MC-head amplifier.
Turn on the power to the component.
Connect the source component to the DIGITAL
INPUT jacks of this unit.
Set “OPTION 2 MEM. GUARD” in the set menu
to OFF.
Disconnect the AC power cord from the outlet
and then plug it in again after about 30 seconds.
Make sure all speaker cables are connected
correctly.
Move this unit further away from such
equipment.
Wait until the unit cools down and then turn it
back on.
Refer to
page
43
10 – 12
TROUBLESHOOTING
0111RX-V740_60-66_EN-GB.p65 03.2.12, 4:30 PM62
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha RX-V740 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha RX-V740 in the language / languages: English as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha RX-V740

Yamaha RX-V740 User Manual - German - 68 pages

Yamaha RX-V740 User Manual - Swedish - 67 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info