516936
102
Zoom out
Zoom in
Previous page
1/125
Next page
En 102
APPENDIX
Refer to the table below when this unit does not function properly.
If the problem you are experiencing is not listed below, or if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service
center.
General
Troubleshooting
Problem Cause Remedy
See
page
The power will not
turn on.
The protection circuitry operated
3 times consecutively.
As a safety precaution, when the protection
circuitry operates 3 times consecutively, the
capability to turn on the power is disabled.
Contact your nearest Yamaha dealer or
service center to request repair.
The unit enters
standby mode soon
after the power is
turned on.
The power cable is not completely
inserted.
Connect the power cable properly to an AC
wall outlet.
(When this unit is turned back on
and “CHECK SP WIRES!” is
displayed.) The protection
circuitry has been activated
because this unit was turned on
while a speaker cable was shorted.
Make sure that all speaker cables between
this unit and speakers are connected
properly.
19
This unit cannot be
turned off or does
not work properly.
The internal microcomputer is
hung-up due to an external electric
shock (such as lightning or
excessive static electricity) or by a
drop in power supply voltage.
Disconnect the power cable from the AC
wall outlet, wait about 30 seconds and then
plug it in again.
The batteries in the remote control
may have lost their charge.
Replace all batteries. 7
The unit enters
standby mode.
The protection circuitry has been
activated because of a short circuit,
etc.
Check that the speaker with an impedance
of at least 6 Ω.
Check that the speaker impedance settings
are correct.
18
Check that the speaker wires are not
touching each other, then turn the unit back
on.
The sleep timer has turned off the
unit.
Turn on the unit, and play the source again.
After display of a
countdown on the
front panel, the unit
goes into standby
mode.
If you do not use take any action,
the Auto Power Down function
operates.
Turn on the unit, and play the source again.
In the Setup menu “Auto Power Down”
(“Function “Auto Power Down”),
increase the time until switching to standby
mode, or turn off the Auto Power Down
function.
88
No sound. Incorrect input or output cable
connections.
Connect the cables properly. If the problem
persists, the cables may be defective.
25
Speaker connections are not
secure.
Secure the connections. 19
The HDMI components connected
to the unit do not support the
HDCP copy protection standards.
Connect HDMI components that support the
HDCP copy protection standards.
The audio input into the device is
set to playback through the TV.
In the Setup menu, set the “Amp” of “Audio
Output” (“HDMI” “Audio Output”
“Amp”) to “On.
87
No appropriate input source has
been selected.
Select an appropriate input source with
Input selector.
40
The volume is turned down or
muted.
Turn up the volume.
Signals that this unit cannot
reproduce are being input from a
source component, such as a CD-
ROM.
Use an input source that has signals that can
be reproduced on this unit.
Problem Cause Remedy
See
page
102


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha RX-V667 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha RX-V667 in the language / languages: English as an attachment in your email.

The manual is 13,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha RX-V667

Yamaha RX-V667 Quick start guide - English - 8 pages

Yamaha RX-V667 User Manual - German - 125 pages

Yamaha RX-V667 Quick start guide - German - 8 pages

Yamaha RX-V667 Quick start guide - Dutch - 8 pages

Yamaha RX-V667 User Manual - Dutch - 125 pages

Yamaha RX-V667 User Manual - French - 124 pages

Yamaha RX-V667 Quick start guide - French - 8 pages

Yamaha RX-V667 User Manual - Italian - 124 pages

Yamaha RX-V667 Quick start guide - Italian - 8 pages

Yamaha RX-V667 User Manual - Swedish - 125 pages

Yamaha RX-V667 Quick start guide - Swedish - 8 pages

Yamaha RX-V667 User Manual - Spanish - 124 pages

Yamaha RX-V667 Quick start guide - Spanish - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info