549977
53
Zoom out
Zoom in
Previous page
1/60
Next page
53
English
Remote control
Others
SYMPTOM
The remote control does not work.
The sound is degraded when
listening with the headphones to a
CD player or tape deck that is
connected to this unit.
There is noise interference from
digital or high-frequency equipment
or the unit.
CAUSE
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
The manufacturer’s code has not been
set properly.
The proper manufacturer’s code for the
component to be controlled has not
been set.
The component to be controlled has not
been selected.
This unit is in the standby mode.
The unit is too close to the digital or
high-frequency equipment.
REMEDY
Change the position of this unit.
Set the code again.
Try entering another code for the same
manufacturer.
Set the SELECTOR DIAL to the proper
position.
Turn on the power of the unit.
Move the unit further away from such
equipment.
SYMPTOM
A loud hissing noise is heard when you
play back a source encoded with DTS.
A percussive noise is heard when you
begin playing back a source encoded
with DTS.
No sound is heard when you play back
a source encoded with DTS, even
though the AUTO input mode is
selected on this unit.
No sound is heard when you play back
an MD or DAT on to which you have
recorded a source encoded with DTS.
No sound is heard when you play back
a source (CD, etc.) even though the
currently selected input mode is AUTO.
CAUSE
The player which plays back the source
is not connected to a digital audio signal
input terminal of this unit.
The ANALOG input mode is selected on
this unit.
If the AUTO input mode is selected,
depending on some sources, there may
be a case that a noise is heard while
this unit is identifying the format of the
input signal.
The DTS decoder built into this unit
does not function because the player
has a digital volume control and it is set
at a position other than “maximum,”
“neutral” or “ineffective.”
A source encoded with DTS cannot be
recorded on to an MD or DAT.
In the AUTO mode, the DTS-decoding
mode cannot be automatically changed
to the normal (PCM) digital signal input
mode.
REMEDY
The player must be connected to a
digital audio signal input terminal of this
unit besides the analog audio signal
terminal connections.
Select a proper input mode on this unit
to turn on the DTS decoder built into
the unit.
Set the input mode of the currently
selected input source to DTS.
Set the player’s digital volume control
at the maximum, neutral or ineffective
position.
Press INPUT MODE on the front panel
or INPUT (for the currently selected
source) on the remote control so that
AUTO appears on the display.
When playing back a source encoded with DTS
Notes
It is necessary to use a DTS decoder to play back a source encoded with DTS, so the player which plays back the source must
be connected to a digital audio input terminal of this unit in the way described in this manual. If this connection is not made or
only a D-to-A converter is being used without using a DTS decoder, when you play back the source, only a loud hissing noise will
be heard.
If you make a search (or skip, etc.) operation while playing back a source encoded with DTS, the “dts” indicator goes out from the
display. This is because this unit automatically changes the DTS-decoding mode to the standard (PCM) digital signal input mode
to prevent a noise from being output.
01RX-V595aRDS-7 6/24/99, 11:02 AM53
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha RX-V595aRDS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha RX-V595aRDS in the language / languages: English as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info