516935
83
Zoom out
Zoom in
Previous page
1/96
Next page
En 83
Audio
Problem Cause Remedy
No sound.
No appropriate input source has been selected. Select an appropriate input source with the input selection key.
Signals that the unit cannot reproduce are being input from a source
device, such as a CD-ROM.
Use an input source that has signals that can be reproduced on the unit.
The mute function is activated. Press MUTE to unmute.
The volume cannot be increased.
The cable between the unit and the external device may be
malfunctioning.
Make sure that all speaker cables between the unit and speakers are
connected properly. If after checking you can find no problems, replace the
cables.
The max volume of the unit is restricted by “Max Volume” function. Adjust the max volume of the unit in “Max Volume” in the “Setup” menu.
The device connected to the output jack of the unit is not turned on.
(This may occur because of the character of AV receiver.)
Turn on all devices connected to the unit.
No sound is output from one speaker.
Sound may not be output from certain channels, depending on the
input source.
You can confirm the number of source channels in the input signal with
“Channel (Chan)” of “Signal Info” in the “Option” menu (p.61).
Sound may not be output from certain channels, depending on the
sound program or decoder.
You can confirm the number of output channels with the speaker indicators on
the front display (p.8).
Output from the affected speaker is disabled.
Perform YPAO (p.29), or set the size or enable the affected speaker in
“Configuration” (p.65) on the “Setup” menu.
The volume of the affected speaker is set excessively low.
Perform YPAO (p.29), or adjust the volume level of the affected speaker in
“Level” (p.66) on the “Setup” menu.
The cable between the unit and the external device may be
malfunctioning.
Make sure that all speaker cables between the unit and speakers are
connected properly. If no problem, replace the cables.
The affected speaker may be malfunctioning.
Replace the affected speaker with another speaker that is operating correctly
to confirm whether the speaker is malfunctioning. If no sound comes from the
replacement speaker, the unit may be malfunctioning.
“Max Volume” is set to a low value. Set it to a higher value.
The speakers that have a problem cannot be confirmed. Use “Test Tone” to confirm the speakers that do not output sounds (p.67).
No sound is heard from the surround
back speakers.
“Extended Surround” is set to “Off.” Set “Extended Surround” to a decoder or “Auto” (p.61).
No sound is heard from the subwoofer.
The source does not contain LFE or low frequency signals.
To confirm, set “Extra Bass” to “On” to output the low frequency sound of the
front channel from the subwoofer (p.66).
The subwoofer is inactive. Perform YPAO (p.29), or set “Subwoofer” to “Use” in the “Setup” menu (p.66).
The subwoofer is tuned off. Turn on the subwoofer.
The volume of the subwoofer is set to a low value. Set it to a higher value.
No sound from a device connected
using an HDMI cable.
The connected HDMI device does not support high-bandwidth digital
copyright protection (HDCP).
You can confirm if message concerning HDMI error is displayed in “Signal
Info” in the “Option” menu (p.61).
HDMI input audio is set to not output from the speakers. Set “Amp” to “On” in “Audio Output” of the “Setup” menu (p.73).
The number of devices is over the limit. Disconnect some of the HDMI devices.
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha RX-V571 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha RX-V571 in the language / languages: English as an attachment in your email.

The manual is 17,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha RX-V571

Yamaha RX-V571 Quick start guide - English - 8 pages

Yamaha RX-V571 User Manual - German - 96 pages

Yamaha RX-V571 Quick start guide - German - 8 pages

Yamaha RX-V571 Quick start guide - Dutch - 8 pages

Yamaha RX-V571 User Manual - Dutch - 96 pages

Yamaha RX-V571 User Manual - French - 96 pages

Yamaha RX-V571 Quick start guide - French - 8 pages

Yamaha RX-V571 User Manual - Italian - 96 pages

Yamaha RX-V571 Quick start guide - Italian - 8 pages

Yamaha RX-V571 User Manual - Swedish - 96 pages

Yamaha RX-V571 Quick start guide - Swedish - 8 pages

Yamaha RX-V571 User Manual - Spanish - 96 pages

Yamaha RX-V571 Quick start guide - Spanish - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info