464173
51
Zoom out
Zoom in
Previous page
1/332
Next page
47 En
English
INTRODUCTION
ADDITIONAL
INFORMATION APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
In the advanced setup, you can set basic operations of this
unit, such as on and off of a bi-amp connection, or
initialize user settings. Perform the following steps to
change settings.
1 Set this unit to the standby mode.
2 Press ASTANDBY/ON while pressing and
holding LSTRAIGHT on the front panel.
The advanced setup menu appears on the front panel
display.
3 Press KPROGRAM l / h repeatedly to
select the parameter you want to change.
The default setting are marked with “*.
y
Set values are placed in XXX of the following parameters on an
actual display screen.
REMOTE ID -XXX
Sets a remote control ID. When using multiple
Yamaha AV receivers, you can operate them with a
single remote control by setting the receiver IDs to
the same setting.
BI AMP - XXX
Switches on and off of bi-amp connection of main
speakers. For bi-amp connection, see page 12.
MON.CHK - XXXX
Adds upscaling limitation on output signals to a video
monitor connected to this unit via the HDMI OUT
jack.
INIT-XXXXXXXXX
Initializes various settings stored in this unit. You can
select an initialization method from the following.
DSP PARAM: All parameters of sound field
programs
VIDEO: Video conversion settings (resolution/
aspect) in the setup menu and the OSD
display position
ALL: Reset this unit to initial factory
settings
CANCEL: Cancellation of initialization
4 Press LSTRAIGHT a few times to select the
value you want to change.
The value selected here becomes effective when this
unit is turned on the next time. You can change
multiple settings by repeating steps 3 and 4.
5 Press ASTANDBY/ON, turns off this
system, and press ASTANDBY/ON again.
The value set in step 3 becomes effective, and this
unit turns on. When you select initialization in step 3,
the initialization is performed.
Two IDs are provided for the remote control of this unit. If
another Yamaha amplifier is in the same room, setting a
different remote control ID to this unit prevents unwanted
operation of the other amplifier.
ID1 is set for both remote control and amplifier by default.
When you change the remote control ID, display
Advance Setup” (see the previous section) and change the
ID for the amplifier too.
1 Press cCODE SET on the remote control
using a pointed object such as the tip of a
ballpoint pen.
bTRANSMIT blinks twice.
2 Press lSETUP on the remote control.
3 Enter the desired remote control ID code.
To switch to ID1:
Enter “5019” using sNumeric keys.
To switch to ID2:
Enter “5020” using sNumeric keys.
Once the remote control code is registered,
bTRANSMIT blinks twice.
If it fails, bTRANSMIT blinks six times. Repeat
from step 1.
y
Initializing the remote control code (see page 46) returns it to ID1.
Advanced setup
Choices: ID1*/ID2
Choices: ON/OFF*
Choices: YES*/SKIP
Choices: DSP PARAM/VIDEO/ALL/CANCEL
ADVANCEDSETUP
Setting a remote control ID
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha RX-V565 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha RX-V565 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 6,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha RX-V565

Yamaha RX-V565 User Manual - English - 268 pages

Yamaha RX-V565 User Manual - Dutch - 76 pages

Yamaha RX-V565 User Manual - French, Italian, Spanish - 268 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info