If you desire to program functions not included in the basic operations covered by the manufacturer code, or a manufacturer code is not
available, the following procedure needs to be performed. The possible programming area is the same as a component control area, so
buttons are programmable independently for each source component area. It is also possible to program in the main unit control area.
1
1
Place this remote control and the other remote control about
5 to 10 cm (2 to 4 in.) apart on a flat surface so that their
infrared transmitters are aimed at each other.
2
2
Select a source component.
3
3
Press LEARN using a ball point pen or similar object.
Do not press and hold LEARN longer than three seconds.
Otherwise this unit enters the Setting the Manufacture Code
mode.
4
4
Press and release the button where you want the new
function to be programmed.
5
5
Press and hold the button on the other remote control that
has the function you want to program into this remote
control until “OK” appears in the display window.
•“NG” appears in display window when programming is
not done correctly. Repeat step 4 until “OK” appears in
the display.
6
6
Repeat Steps 4 and 5 to program additional functions.
7
7
Press LEARN again to exit the Learn mode.
Notes:
•If you do not press any button within 30 seconds, the learning process is canceled.
•This remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of the other remote
control’s functions. However, you may not be able to program some special signals or extremely long transmissions. (Refer to the operation instructions for
the other remote control.) When the memory is full, “FULL” appears in the display window, and this remote control cannot acquire any more functions.
Clear unnecessary programmed functions to allow the unit to acquire new functions.
•Even if the batteries in the other remote control have enough power to transmit signals for operation, they may not have enough power to transmit signals to
this remote control.
•When the remote controls are either too close together or too far apart, you may not be able to program this remote control.
•Direct sunlight interferes with infrared rays.
•“ERROR” appears in the display window in the following conditions: when pressing more than one button at once; and when MACRO ON/OFF is
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Yamaha RX-V3000RDS at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Yamaha RX-V3000RDS in the language / languages: English as an attachment in your email.
The manual is 7,5 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
