492656
135
Zoom out
Zoom in
Previous page
1/151
Next page
En 135
Audio
Problem Cause Remedy
No sound.
Another input source is selected. Select an appropriate input source with the input selection keys
Signals that this unit cannot reproduce are being input.
Some digital audio formats cannot be played back on this unit. To check the
audio format of the input signal, use “Audio Signal” in the “Information” menu
(p.118).
The cable connecting this unit and playback device is defective. If there is no problem with the connection, replace with another cable.
The volume cannot be increased.
The maximum volume is set. Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.108).
Any device connected to the output jacks of this unit is not turned
on. (This may happen due to the nature of AV receivers.)
Turn on all devices connected to the output jacks of this unit
No sound is heard from a specific
speaker.
The playback source does not contain corresponding channel
signals.
To check it, select “9ch Stereo” (p.55).
The sound program/decoder currently selected does not use the
corresponding speaker.
To check it, select “9ch Stereo” (p.55).
Audio output of the corresponding speaker is disabled.
Perform “Auto Setup” (p.45) or use “Configuration” in the “Setup” menu to change
the speaker setting (p.105).
The volume of the corresponding speaker is too low.
Perform “Auto Setup” (p.45) or use “Level” in the “Setup” menu to adjust the
speaker volume (p.106).
The speaker cable connecting this unit and corresponding
speaker is defective.
If there is no problem with the connection, replace with another speaker cable.
The corresponding speaker is malfunctioning.
To check it, replacing with another speaker. If the problem persists, this unit may
be malfunctioning.
No sound is heard from the surround
back speaker.
The extended surround is disabled.
Use “Extended Surround” in the “Option” menu to select a decoder to be used
(p.92).
No sound is heard from the subwoofer.
The playback source does not contain LFE or low-frequency
signals.
To check it, set “Extra Bass” in the “Setup” menu to “On”, to output the front
channel low-frequency components from the subwoofer (p.106).
Subwoofer output is disabled.
Perform “Auto Setup” (p.45) or set “Subwoofer 1” or “Subwoofer 2” in the “Setup”
menu to “Use” (p.106).
The subwoofer is turned off by the auto-standby function on it. Disable the auto-standby function of the subwoofer or adjust its sensitivity level.
No sound from the playback device
(connected to this unit with HDMI).
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
To check it, use “Video Signal” in the “Information” menu (p.118).
This unit is set not to output audio input through HDMI jacks from
the SPEAKERS terminals.
In “Audio Output” in the “Setup” menu, set “Amp” to “On” (p.112).
The number of devices connected to the HDMI OUT jack is over
the limit.
Disconnect some of the HDMI devices.
No sound from the TV (when HDMI
Control is used).
(If the TV is connected to this unit with an audio cable)
The TV audio input setting does not match the actual connection.
Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack
(p.111).
(If you are trying to use ARC)
ARC is disabled on this unit or TV.
Set “ARC” in the “Setup” menu to “On” (p.111). Also, enable ARC on the TV.
135


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha RX-A2010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha RX-A2010 in the language / languages: English as an attachment in your email.

The manual is 13,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha RX-A2010

Yamaha RX-A2010 Quick start guide - English - 8 pages

Yamaha RX-A2010 User Manual - Dutch - 151 pages

Yamaha RX-A2010 Quick start guide - Dutch - 8 pages

Yamaha RX-A2010 User Manual - Danish - 151 pages

Yamaha RX-A2010 User Manual - French - 151 pages

Yamaha RX-A2010 User Manual - Swedish - 151 pages

Yamaha RX-A2010 User Manual - Spanish - 151 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info