635416
105
Zoom out
Zoom in
Previous page
1/121
Next page
105
A strange “flanging” or “doubling” sound
occurs when using the PortaTone with a
sequencer. (This may also sound like a “dual”
layered sound of two voices, even when Dual
is turned off.)
• If you are routing the MIDI OUT on the PortaTone to a sequencer
and back to the MIDI IN, you may want to set Local Control (page
97) to “off” to avoid MIDI “feedback.”
• When using the accompaniment with a sequencer, set MIDI Echo
(or the relevant control) to “off.” (Refer to the owner’s manual of
your particular device and/or software for details.)
The footswitch seems to produce the opposite
effect. For example, when using the footswitch
for sustain, pressing the footswitch cuts off the
sound and releasing it sustains the sounds.
The polarity of the footswitch is reversed. Make sure that the
footswitch plug is properly connected to the FOOT SWITCH jack
before turning on the power.
The AWM tone generation method uses multiple recordings
(samples) of an instrument across the range of the keyboard; thus,
the actual sound of the voice may be slightly different from note to
note.
The sound of the voice changes from note to
note.
Problem Possible Cause and Solution
TROUBLESHOOTING
DATA BACKUP & INITIALIZATION
Except for the data listed below, all PSR-225 panel settings are reset to their initial settings
whenever the power is turned on. The data listed below are backed up — i.e. retained in
memory — as long as an AC adaptor is connected or a set of batteries is installed.
• User Song Data • Metronome Volume
• User One Touch Setting Data • Touch On/Off
• One Touch Setting Bank Number • Touch Sensitivity
• EZ Chord Data • Split Point
• EZ Chord Bank Number Data • Accompaniment Split Point
• Smart Chord Number • Footswitch Assign Function
CLr
Backup
VOICE
STYLE
• All one touch setting
(user) and song memory
data, plus the other settings
listed above, will be erased
and/or changed when the
data initialization proce-
dure is carried out.
• Carrying out the data
initialization procedure will
usually restore normal
operation if the PSR-225
freezes or begins to act
erratically for any reason.
Data Initialization
All data can be initialized and restored to the factory preset condition by turning on the
power while holding the highest (rightmost) white key on the keyboard. “CLr Backup” will
appear briefly on the display.
105


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha PSR-225GM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha PSR-225GM in the language / languages: English as an attachment in your email.

The manual is 3,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha PSR-225GM

Yamaha PSR-225GM User Manual - German - 121 pages

Yamaha PSR-225GM User Manual - Dutch - 118 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info