555592

Yamaha NS-PA40 Manual

9
Zoom out
Zoom in
Previous page
1/76
Next page
6 En
Using the Subwoofer
English
Caution
• To move the front speaker to another location, grasp
both the Base and Bottom.
• If a cable comes off a notch, affix the cable into the
notch using adhesive tape.
• Make sure that children do not lean on the speaker.
Otherwise, it may tip over, possibly resulting in
personal injury.
■ Connecting the speakers
Connect each speaker to the appropriate speaker
terminals on your amplifier by using the cables you
prepared earlier. See the “Connection diagram” on
page 4 for reference.
Make sure you connect the speakers with the correct
polarity—positive (+) terminals to positive (+)
terminals, and negative (–) terminals to negative (–)
terminals. If you get them crossed over, the sound will
be unnatural and lack bass.
In your AV receiver’s speaker size settings, specify
small (or “S”) for all of the NS-PA40 speakers.
If you’re connecting the subwoofer to a Yamaha DSP
amplifier or AV receiver, connect to its SUBWOOFER
or LOW PASS output.
Connecting the power cables
Once you’ve completed all of the speaker and
subwoofer connections, plug the subwoofer, amplifier,
and your other AV components into suitable AC wall
outlets.
1 Power indicator
Lights up when the POWER switch is set to ON;
goes off when the POWER switch is set to OFF.
2 INPUT jack
Input jack for connecting the line-level subwoofer
output on your amplifier.
3 VOLUME control
Adjusts the volume of the subwoofer. Turn it
clockwise to increase the volume;
counterclockwise to decrease the volume.
4 POWER switch
Set this to ON to turn on the subwoofer. Set it to
OFF to turn off the subwoofer.
Setting the subwoofer volume
The very first time you use the subwoofer, you need to
set the volume balance between the subwoofer and the
front speakers as follows.
1 Turn on your other AV components.
2 Set the subwoofer’s VOLUME control to
minimum (0).
3 Set the subwoofer’s POWER switch to ON.
The power indicator on the rear panel lights up.
4 Play a audio source that contains low-
frequency bass sounds. Set the amplifier’s
volume control to a suitable level.
5 Turn the subwoofer’s VOLUME control up
gradually until you achieve a good balance
between the subwoofer and the other
speakers.
Note
• Once the subwoofer volume has been set, you can
leave the subwoofer’s VOLUME control set as it is
and use your amplifier’s volume control to adjust the
volume of the entire system.
• If you replace the front speakers (NS-F40) with
other speakers, you will need to re-adjust the
subwoofer’s volume.
Remove all protective sheet from the unit before use.
Using the Subwoofer
1
2
3
4
Rear panel
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha NS-PA40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha NS-PA40 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info