Manual Yamaha NP-30 (page 20 of 40) (English)

635443

Zoom out

Zoom in

1/40

NP-30

YNP-25

Digital Keyboard

Owner’s Manual

NP-30/YNP-25 Owner’s Manual

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter). DO

NOT connect this product to any power supply or adapter other than one

described in the manual, on the name plate, or speciﬁcally recom-

mended by Yamaha.

WARNING: Do not place this product in a position where anyone could

walk on, trip over, or roll anything over power or connecting cords of any

kind. The use of an extension cord is not recommended! If you must use

an extension cord, the minimum wire size for a 25’ cord (or less) is 18

AWG. NOTE: The smaller the AWG number, the larger the current han-

dling capacity. For longer extension cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or modify

any of the speciﬁcations without notice or obligation to update existing

units.

This product, either alone or in combination with an ampliﬁer and head-

phones or speaker/s, may be capable of producing sound levels that

could cause permanent hearing loss. DO NOT operate for long periods

of time at a high volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should consult an

audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory mounting

ﬁxtures that are either supplied with the product or as optional accesso-

ries. Some of these items are designed to be dealer assembled or

installed. Please make sure that benches are stable and any optional ﬁx-

tures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your dealer

before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environ-

mentally friendly. We sincerely believe that our products and the produc-

tion methods used to produce them, meet these goals. In keeping with

both the letter and the spirit of the law, we want you to be aware of the

following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately ﬁve years. When replacement becomes necessary,

contact a qualiﬁed service representative to perform the replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, do not mix batteries with new, or with batteries

of a different type. Batteries MUST be installed correctly. Mismatches or

incorrect installation may result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all batter-

ies away from children. Dispose of used batteries promptly and as regu-

lated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some reason

its useful life is considered to be at an end, please observe all local,

state, and federal regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc. If your dealer is unable to assist

you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model num-

ber, serial number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the date of pur-

chase in the spaces provided below and retain this manual as a perma-

nent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

NP-30/YNP-25 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please contact

Yamaha Corporation of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

Entsorgung leerer Batterien (nur innerhalb Deutschlands)

Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte Batterien

oder Akkumulatoren dürfen nicht in den Hausmüll. Sie können bei

einer Sammelstelle für Altbatterien bzw. Sondermüll abgegeben wer-

den. Informieren Sie sich bei Ihrer Kommune.

(class B)

(battery)

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den

ar ansluten till vägguttaget, även om själva apparaten har stängts av.

ADVARSEL: Netspæendingen til dette apparat er IKKE afbrudt,

sålæenge netledningen siddr i en stikkontakt, som er t endt — også

selvom der or slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko

laitetta verkosta.

(standby)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in accor-

dance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured makings identifying the ter-

minals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the ter-

minal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal

of the three pin plug.

• This applies only to products distributed by Yamaha-Kemble

Music (U.K.) Ltd.

(2 wires)

NP-30/YNP-25 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the speciﬁed adaptor (PA-5D, PA-150 or an equivalent recommended by

Yamaha) only. Using the wrong adaptor can result in damage to the instrument

or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Do not place the AC adaptor cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy objects

on it, or place it in a position where anyone could walk on, trip over, or roll

anything over it.

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings. If any liquid such as water seeps into the instrument, turn off the

power immediately and unplug the power cord from the AC outlet. Then have the

instrument inspected by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the instrument, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power switch,

disconnect the adaptor plug from the outlet, and have the instrument inspected

by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord.

• Unplug the AC power adaptor when not using the instrument, or during

electrical storms.

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• Always make sure all batteries are inserted in conformity with the +/- polarity

markings. Failure to do so might result in overheating, ﬁre, or battery ﬂuid

leakage.

• Always replace all batteries at the same time. Do not use new batteries together

with old ones. Also, do not mix battery types, such as alkaline batteries with

manganese batteries, or batteries from different makers, or different types of

batteries from the same maker, since this can cause overheating, ﬁre, or battery

ﬂuid leakage.

• Do not dispose of batteries in ﬁre.

• Do not attempt to recharge batteries that are not intended to be charged.

• When the batteries run out, or if the instrument is not to be used for a long time,

remove the batteries from the instrument to prevent possible leakage of the

battery ﬂuid.

• Keep batteries away from children.

• If the batteries do leak, avoid contact with the leaked ﬂuid. If the battery ﬂuid

should come in contact with your eyes, mouth, or skin, wash immediately with

water and consult a doctor. Battery ﬂuid is corrosive and may possibly cause

loss of sight or chemical burns.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disﬁguration or damage to the internal

components.

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Otherwise, the instrument, TV, or radio may

generate noise.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Battery

Location

(4)-12 1/2

NP-30/YNP-25 Owner’s Manual

• Before moving the instrument, remove all connected adaptor and other cables.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• Use only the stand speciﬁed for the instrument. When attaching the stand or

rack, use the provided screws only. Failure to do so could cause damage to the

internal components or result in the instrument falling over.

• Do not place objects in front of the instrument’s air vent, since this may prevent

adequate ventilation of the internal components, and possibly result in the

instrument overheating.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum. Also, be sure to set the volumes of all

components at their minimum levels and gradually raise the volume controls

while playing the instrument to set the desired listening level.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning ﬂuids, or chemical-impregnated wiping cloths.

• Do not insert a ﬁnger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel

or keyboard. If this happens, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected by qualiﬁed

Yamaha service personnel.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

Always turn the power off when the instrument is not in use.

When using a power adaptor, even when the power switch is in the “STANDBY” position, electricity is still ﬂowing to the instrument at the minimum level. When you are not

using the instrument for a long time, make sure you unplug the AC power adaptor from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

Connections

Maintenance

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument.

PRECAUTIONS

(4)-12 2/2

NP-30/YNP-25 Owner’s Manual

Introduction

Thank you for purchasing the Yamaha NP-30/YNP-25!

We recommend that you read this manual carefully

so that you can fully take advantage of the advanced and

convenient functions of the NP-30/YNP-25.

We also recommend that you keep this manual in a safe and

handy place for future reference.

Main Features

Graded Touch Keyboard

Features well balanced weight gradations of the keys—heavy in the lower end, light in the upper keys.

AWM Stereo Sampling

The Yamaha NP-30/YNP-25 offers unmatched sonic realism and natural grand-piano type playability as well as

Yamaha’s original “AWM Stereo Sampling” tone-generation technology for rich, musical voices.

In particular, the Grand Piano 1 and 2 voices feature samples painstakingly recorded from a full concert grand piano,

while the Electric Piano 1 and 2 voice features multiple samples for different velocities (Dynamic Sampling); in other

words, it uses different samples depending on the strength of your playing.

NP-30/YNP-25 Owner’s Manual

About this Owner’s Manual

This manual consists of three main sections: Introduction, Reference and Appendix.

Introduction (page 6):

Please read this section ﬁrst.

Reference (page 14):

This section explains how to make detailed settings for the instrument’s various functions.

Appendix (page 28):

This section features a variety of essential, detailed information on the instrument.

*The illustrations as shown in this owner’s manual are for instructional purposes only, and may appear somewhat different from

those on your instrument.

*Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited

except for your personal use.

*For the sake of simplicity, both models NP-30 and NP-30S are hereafter referred to in this Owner’s Manual as NP-30.

•The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective

companies.

Accessories

• Owner’s Manual

This manual contains complete instructions for operating your instrument.

• Quick Operation Guide

• Music Rest

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to

which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style

ﬁles, MIDI ﬁles, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of

personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE

OR USE ILLEGAL COPIES.

NP-30/YNP-25 Owner’s Manual

Tab le of Contents

Introduction

Main Features...............................................................................................6

About this Owner’s Manual .........................................................................7

Accessories ...................................................................................................7

Application Index .........................................................................................9

Panel Controls and Terminals....................................................................10

Before Using...............................................................................................11

Power Requirements ................................................................................................... 11

Turning the Power On ................................................................................................ 12

Setting the Volume...................................................................................................... 13

Using the Pedal ............................................................................................................ 13

Using Headphones ...................................................................................................... 13

Music Rest.................................................................................................................... 13

Reference

Listening to the Demo Songs ....................................................................14

Listening to the Piano Preset Songs..........................................................15

Using the Metronome................................................................................16

Selecting & Playing Voices.........................................................................18

Selecting Voices ........................................................................................................... 18

Combining Voices (Dual)........................................................................................... 19

Adding Variations to the Sound – Reverb ................................................................. 20

Transposition............................................................................................................... 21

Fine tuning of the Pitch............................................................................................... 21

Touch Sensitivity ......................................................................................................... 22

Connecting MIDI Instruments ...................................................................23

Connecting MIDI [IN] [OUT] terminals .................................................................. 23

MIDI’s Capability ........................................................................................................ 23

Connecting a Personal Computer .............................................................................. 24

MIDI Functions ...........................................................................................25

MIDI Transmit/Receive Channel Selection ............................................................... 25

Local Control ON/OFF ............................................................................................... 25

Program Change ON/OFF.......................................................................................... 26

Control Change ON/OFF ........................................................................................... 26

Troubleshooting.........................................................................................27

Optional Equipment...................................................................................27

Appendix

MIDI Data Format ......................................................................................28

MIDI Implementation Chart ......................................................................32

Specifications .............................................................................................34

Index...........................................................................................................35

NP-30/YNP-25 Owner’s Manual

Application Index

Use this index to ﬁnd reference pages that may be helpful for your particular application and situation.

Listening

Listening to demo songs with different voices.....................................................................Listening to the Demo Songs on page 14

Playing

Using the sustain pedal ............................................................................................................................... Using the Pedal on page 13

Changing the key of the NP-30/YNP-25 to facilitate playing in difﬁcult/unfamiliar key signatures ........Transposition on page 21

Fine tuning the pitch of the entire instrument when you play the instrument along with other instruments or CD music

.........................................................................................................................................................Fine tuning of the Pitch on page 21

Selecting a touch sensitivity type............................................................................................................. Touch Sensitivity on page 22

Using a built-in metronome............................................................................................................ Using the Metronome on page 16

Changing voices

Viewing the list of voices ............................................................................................................................Selecting Voices on page 18

Simulating a concert hall ..................................................................................Adding Variations to the Sound – Reverb on page 20

Combining two voices ............................................................................................................... Combining Voices (Dual) on page 19

Connecting the NP-30/YNP-25 to other devices

What is MIDI?..................................................................................................................................................About MIDI on page 23

Connecting a computer ................................................................................................ Connecting a Personal Computer on page 24

Panel Controls and Terminals

NP-30/YNP-25 Owner’s Manual

Panel Controls and Terminals

1 [STANDBY/ON] switch ................ page 11

For turning the power on or off.

2 [MASTER VOLUME] slider ........... page 13

For adjusting the volume level of the entire sound.

3 [METRONOME ON/OFF] button

..................................................... page 16

For using the metronome.

4 [SONG

] button................ page 14, 15

For playing the demo songs and the piano preset

songs.

5 [GRAND PIANO] button

..........................................page 18-20, 22

For selecting voices from 10 internal sounds includ-

ing Grand Piano 1 and 2 (page 18). You can also

combine two voices (page 19) or add reverb effects to

the selected voice for your keyboard performance

(page 20).

6 VOICE/SONG [BACK<<], [>>NEXT]

button ............................ pages 14, 15, 18

While playing a voice demo or piano preset song,

pressing these buttons can be selected next or previ-

ous song. These buttons can be also changed a voice.

7 [SUSTAIN] jack .............................page 13

For connecting an optional pedal (FC5), FC3 foot

pedal or FC4 foot switch.

8 MIDI [IN] [OUT] terminals ...........page 23

For connecting external MIDI devices, allowing the

use of various MIDI functions.

9 [PHONES/OUTPUT] jack ..............page 13

For connecting a set of standard stereo headphones,

allowing private practice.

) [DC IN 12V] jack...........................page 11

For connecting the power adaptor.

12 345

Shows the jacks and terminals

as seen when viewed from the

rear of the instrument.

Shows the jacks and terminals

as seen when viewed from the

rear of the instrument.

Before Using

NP-30/YNP-25 Owner’s Manual

Before Using

Be sure to do the following operations BEFORE turning on the power.

Power Requirements

Although the instrument will run either from an optional AC adaptor or batteries, Yamaha recom-

mends use of an AC adaptor whenever possible. An AC adaptor is more environmentally friendly

than batteries and does not deplete resources.

Using an AC Power Adaptor...............................................................

1. Make sure that the [STANDBY/ON] switch

of the instrument is set to STANDBY.

WARNING

Use the speciﬁed adaptor (PA-5D, PA-150, or an equivalent recom-

mended by Yamaha) only. The use of other adaptors may result in

irreparable damage to both the adaptor and the instrument.

2. Connect the AC adaptor to the power sup-

ply jack.

3. Plug the AC adaptor into an AC outlet.

CAUTION

Unplug the AC Power Adaptor when not using the instrument, or

during electrical storms.

CAUTION

Even when the instrument is turned off, electricity is still ﬂowing to

the instrument at the minimum level.

When you are not using the instrument for a long time, make sure

you unplug the AC power adaptor from the wall AC outlet.

unlit

AC outletAdaptor

Before Using

NP-30/YNP-25 Owner’s Manual

Using Batteries ....................................................................................

1. Open the battery compartment cover

located on the instrument’s bottom panel.

2. Insert the six new alkaline batteries, being

careful to follow the polarity markings on

the side of the compartment.

3. Replace the compartment cover, making

sure that it locks ﬁrmly in place.

For battery operation the instrument requires six 1.5V

“AA” size, LR6 or equivalent batteries. (Alkaline batter-

ies are recommended.) When battery power becomes

too low for proper operation, the volume may be

reduced, the sound may be distorted, and other prob-

lems may occur. When this happens, make sure to

replace all batteries, following the precautions listed

below.

CAUTION

Use alkaline batteries for this instrument. Other types of batteries

(including rechargeable batteries) may have sudden drops of power

when battery power becomes low.

Make sure to install the batteries with the proper orientation, main-

taining the correct polarity (as shown). Incorrect battery installation

may result in heat, ﬁre and/or leaking of corrosive chemicals.

When the batteries run down, replace them with a complete set of six

new batteries. NEVER mix old and new batteries. Do not use different

kinds of batteries (e.g. alkaline and manganese) at the same time.

If the instrument is not to be in use for a long time, remove the bat-

teries from it, in order to prevent possible ﬂuid leakage from the bat-

tery.

Tur ning the Power On

Press the [STANDBY/ON] switch to turn on the power.

The power indicator located to the left of the [STANDBY/ON] switch

lights up.

Pressing the switch again turns the power off.

CAUTION

When using a power adaptor, even when the power is off, a small amount of

electricity is still being consumed by the instrument. When you are not using

the instrument for a long time, make sure to unplug the AC power adaptor

from the wall AC outlet, and/or remove the batteries from the instrument.

Never connect or disconnect the AC power adaptor when the

power is on and the batteries are installed. Doing so will turn

the power off.

NOTE

Before Using

NP-30/YNP-25 Owner’s Manual

Setting the Volume

Initially set the [MASTER VOLUME] slider about halfway between the

“MIN” and “MAX” settings. Then, when you start playing, re-adjust the

[MASTER VOLUME] slider to the most comfortable listening level.

Using the Pedal

[SUSTAIN] jack

This jack is for connecting an optional pedal.

The pedal functions in the same way as a damper pedal on an acoustic

piano. Connect an optional pedal to this jack and press the pedal to sus-

tain the sound.

Do not press the footswitch while turning the power on. Doing this

changes the recognized polarity of the footswitch, resulting in reversed

footswitch operation.

If you connect an optional pedal of FC3, the half pedal function* can be

used.

* half pedal function

While you playing the piano with SUSTAIN and if you need to delete the

cloudy sound, release the foot from pedal to half position.

Using Headphones

Connect a set of headphones to the [PHONES/OUTPUT] jack.

CAUTION

To protect your hearing, avoid listening to the NP-30/YNP-25 at a high vol-

ume level for long periods of time.

Music Rest

The NP-30/YNP-25 includes a music rest that can be attached to the

instrument by inserting it into the slot at the top of the control panel.

CAUTION

Since speakers are built into the instrument you should be careful to never

leave any video tapes, cassette tapes, ﬂoppy disks or any kind of magnetic

storage media on the panel—doing so may result in data loss or damage to

the items. Also avoid using the instrument near a television or computer

monitor, since interference may result.

TERMINOLOGY

MASTER VOLUME:

The volume level of the entire keyboard sound

Make sure that power is OFF when connecting or disconnecting the

pedal.

The level increases.The level decreases.

FC5

NOTE

Listening to the Demo Songs

NP-30/YNP-25 Owner’s Manual

Listening to the Demo Songs

Demo songs are provided that effectively demonstrate each of the voices.

1. Press the [STANDBY/ON] switch to turn the power

on.

When the power is turned ON, the power indica-

tor located to the left of the [STANDBY/ON]

switch lights up.

2. Adjust the volume.

Initially set the [MASTER VOLUME] slider about

half way between the “MIN” and “MAX” settings.

Then, when you start playing, re-adjust the

[MASTER VOLUME] slider to the most comfort-

able listening level.

3. Press the [SONG

] button to lis-

ten to the demo songs.

The GRAND PIANO 1 demo song will start. Demo

songs provided for each voice and the piano preset

songs will play back in sequence until you press the

[SONG

] button.

Changing a Demo Song

You can change to another demo song during play-

back by pressing the VOICE/SONG [BACK<<] or

[>>NEXT]

button. For selecting a demo song using

the keyboard, press one of the C1–A1 keys while

holding down the [SONG

] button.

Demo Song List

• The demonstration pieces listed above are short rearranged excerpts of the original

compositions.

4. Press the [SONG

] button to

stop the voice demo.

Refer to the voice list on page 18

for more information on the char-

acteristics of each preset voice.

The demo songs will not be trans-

mitted via MIDI.

NOTE

KeyVoice Name Title Composer

G1 HARPSICHORD 1 Gavotte J.S. Bach

G#1 HARPSICHORD 2 Invention No. 1 J.S. Bach

C1 A1

Reference

Listening to the Piano Preset Songs

NP-30/YNP-25 Owner’s Manual

Listening to the Piano Preset Songs

The NP-30/YNP-25 provides performance data for piano songs as well as voice demo songs, for

your listening pleasure.

1. While holding down the [SONG

] button, press

one of the C2–A2 keys to select a song to play back.

The number of each piano preset song is assigned to the C2–A2 keys.

While holding down the [SONG

] button, press the A#2 key to play all preset

songs consecutively in sequence.

Piano Preset Song List

Press the VOICE/SONG [BACK<<] or [>>NEXT] but-

ton to change to the next piano song.

2. Press the [SONG

] button to

stop playback.

To continue playing other songs, see step 1 above.

TERMINOLOGY

Song:

On the NP-30/YNP-25, perfor-

mance data is called a “Song.”

This includes demonstration

tunes and piano preset tunes.

Preset:

Preset Data supplied with the

internal memory of the NP-30/

YNP-25 shipped from the factory.

You can play the keyboard along

with the preset song. You can

change the voice playing on the

keyboard.

When you select a different song

(or a different song is selected

during chained playback), an

appropriate reverb type will be

selected accordingly.

The piano preset songs are not

transmitted via MIDI.

NOTE

No. Title Composer

1 Menuett G dur BWV.Anh.114 J.S. Bach

2Turkish March (Piano Sonate No.11 K.331) W.A. Mozart

3 Für Elise L.v. Beethoven

4Valse op.64-1 “Petit chien” F.F. Chopin

5Träumerei R. Schumann

6 Dolly’s Dreaming and Awakening T. Oesten

7Arabesque J.F.F. Burgmüller

8 Humoresque A. Dvorák

9 The Entertainer S. Joplin

10 La Fille aux Cheveux de Lin C.A. Debussy

C1 C2 A2

ALL

Using the Metronome

NP-30/YNP-25 Owner’s Manual

Using the Metronome

This instrument features a built-in metronome (a device that keeps an accurate tempo) that is con-

venient for practicing.

1. Press the [METRONOME ON/OFF]

button to turn on the metronome.

Start the metronome.

Determine the time signature

While holding down the [METRONOME ON/OFF] button, press one of the C3–

F3 keys.

The ﬁrst beat is accented with a bell sound and the rest with clicks.

Default set is 0/4 (C3). In this setting, clicks sound in all beats.

Adjust the Tempo

The tempo of the metronome and song playback can be set from 32 to 280 beats

per minute.

A number is assigned to each of the following keys.

While holding down the [METRONOME ON/OFF] button, press a sequence of

C4–A4 keys to specify a three-digit number.

Select a number starting from the left-most digit. For example, to set the tempo

“95,” press the C4 (0), A4 (9) and F4 (5) keys in sequence.

Key Time signature

C3 0/4

C#3 2/4

D3 3/4

D#3 4/4

E3 5/4

F3 6/4

C3 F3C1 C2

A4C4 C5 C6

Using the Metronome

NP-30/YNP-25 Owner’s Manual

Increasing the tempo value in steps of one:

While holding down the [METRONOME ON/OFF] button, press the C#5 key.

Decreasing the tempo value in steps of one:

While holding down the [METRONOME ON/OFF] button, press the B4 key.

Increasing the tempo value in steps of ten:

While holding down the [METRONOME ON/OFF] button, press the D5 key.

Decreasing the tempo value in steps of ten:

While holding down the [METRONOME ON/OFF] button, press the A#4 key.

Resetting the tempo to default:

While holding down the [METRONOME ON/OFF] button, press the C5 key.

Adjusting the volume

You can change the volume of the metronome sound.

While holding down the [METRONOME ON/OFF] button, press one of the C1–

G2 keys to determine the volume.

Pressing a higher key in the key range results in a higher volume, while pressing

a lower key results in lower volume.

2. Press the [METRONOME ON/OFF]

button to stop the Metronome.

D5 (+10)

B4 (-1)

A#4 (-10)

C#5 (+1)

A#4

C5 (default)

Metronome volume range:

C1 (1)–G2 (20)

Default setting: A1 (10)

NOTE

(1)

(20)

Selecting & Playing Voices

NP-30/YNP-25 Owner’s Manual

Selecting & Playing Voices

Selecting Voices

1. While holding down the [GRAND PIANO] button,

press one of the C1–A1 keys to select a voice.

Pressing the VOICE/SONG [BACK<<] or [>>NEXT]

button switches among the following ten voices.

2. Adjust the volume.

Re-adjust the [MASTER VOLUME] slider for the most comfortable listening

level during your performance.

C1 A1

To familiarize yourself with the

characteristics of the voices, lis-

ten to the demo songs for each

voice (page 14).

TERMINOLOGY

Voice:

On the NP-30/YNP-25, the term

“voice” means “instrument

sound.”

When you select a voice, an

appropriate reverb type will be

selected automatically (page 20).

NOTE

KeyVoice Name Description

C1 Grand Piano 1

Recorded samples from a full concert grand piano. Perfect for clas-

sical compositions as well as any other style that requires acoustic

piano.

C#1Grand Piano 2 Clear piano with bright reverb. Good for popular music.

D1 E. Piano 1 An electronic piano sound created by FM synthesis. Good for

popular music.

D#1E. Piano 2

The sound of an electric piano using hammer-struck metallic “tines.”

Soft tone when played lightly, and an aggressive tone when played

hard.

E1 Church Organ 1

This is a typical pipe organ sound (8' + 4' + 2'). Good for sacred music

from the Baroque period.

F1 Church Organ 2

This is the organ’s full coupler sound, often associated with Bach’s

“Toccata and Fugue.”

F#1

Strings Spacious and large-scale string ensemble. Try combining this voice

with piano in DUAL.

G1 Harpsichord 1

The deﬁnitive instrument for baroque music. Since the strings of a

harpsichord are plucked, there is no touch response.

G#1 Harpsichord 2

Mixes the same voice an octave higher for a more brilliant tone.

A1 Vibraphone

The sound of a vibraphone played with relatively soft mallets.

Selecting & Playing Voices

NP-30/YNP-25 Owner’s Manual

Combining Voices (Dual)

You can play voices simultaneously across the entire range of the keyboard. In this way, you can

combine similar voices to create a thicker sound.

1. While holding down the [GRAND PIANO] button,

press two keys in the range of C1 through A1 simul-

taneously (or press one key while holding another)

to engage Dual.

Refer to “Selecting Voices” on page 18 for more information on the voices that

are assigned to the keys.

The voice assigned to the lower key will be designated as Voice 1, and the voice

assigned to the higher key will be designated as Voice 2.

You can make the following settings for Voices 1 and 2 in Dual:

Setting the Octave

You can shift the pitch up and down in octave steps for Voice 1 and Voice 2 inde-

pendently. Depending on which voices you combine in Dual, the combination

may sound better if one of the voices is shifted up or down an octave.

While holding down the [GRAND PIANO] button, press one of the C4–F4 keys.

Setting the Balance

You can adjust the volume balance between two voices. For example, you can set

one voice as the main voice with a louder setting, and make the other voice softer.

While holding down the [

GRAND

PIANO] button, press one of the F#4–F#5

keys.

A setting of “0” produces an equal balance between the two Dual voices. Settings

below “0” increase the volume of Voice 2 in relation to Voice 1, and settings above

“0” increase the volume of Voice 1 in relation to Voice 2.

2. While holding down the [GRAND PIANO] button,

press one of the C1–A1 keys (or press the [GRAND

PIANO/VOICE] button) to exit Dual and return to

the normal single-voice play.

Reverb in Dual

The reverb type assigned to

Voice 1 will take priority. If the

reverb assigned to Voice 1 is set

to OFF, the reverb assigned to

Voice 2 will be in effect.

NOTE

Voice 1

C4 -1

Voice 2

D#4-1

C#40 E4 0

D4 +1 F4 +1

C1 A1

F4 C5 C6C4

Voice 2Voice 1

C5(0) C6C4

F#5 (+6)F#4 (-6)

Selecting & Playing Voices

NP-30/YNP-25 Owner’s Manual

Adding Variations to the Sound – Reverb

This control enables you to select four different types of reverb effect that add extra depth and

expression to the sound to create a realistic acoustic ambience.

Selecting a Reverb Type

While holding down the [GRAND PIANO] button, press one of the C2–E2 keys

to select a reverb type.

Adjusting Reverb Depth

While holding down the [GRAND PIANO] button, press one of the C3–A#3

keys to adjust the reverb depth for the selected voice.

While holding down the [GRAND PIANO] button, press the B3 key to set the

reverb to the depth most suitable for the selected voice.

KeyReverb Type Description

C2 Room This setting adds a continuous reverb effect to the sound, similar to the

acoustic reverberation you would hear in a room.

C#2 Hall1 For a “bigger” reverb sound, use the HALL 1 setting. This effect simulates

the natural reverberation of a small-size concert hall.

D2 Hall2 For a truly spacious reverb sound, use the HALL 2 setting. This effect sim-

ulates the natural reverberation of a large concert hall.

D#2 Stage Simulates the reverb of a stage environment.

E2 Off No effect is applied.

C1 C2 E2

Reverb depth range:

0 (no effect)–

10 (maximum depth)

NOTE

B3C1 C2

The depth value increases as you press higher keys.

A#3: depth 10

C3: depth 0

The default reverb type (including

OFF) and depth settings are dif-

ferent for each voice.

NOTE

Selecting & Playing Voices

NP-30/YNP-25 Owner’s Manual

Transposition

The Transpose function makes it possible to shift the pitch of the entire keyboard up or down in

semitone intervals to facilitate playing in difﬁcult key signatures, and to let you easily match the

pitch of the keyboard to the range of a singer or other instruments. For example, if you set the

transposition amount to “+5,” playing key C produces pitch F. In this way, you can play a song as

though it were in C major, and the NP-30/YNP-25 will transpose it to the key of F.

Setting the amount of transposition

While holding down the [SONG

] and [GRAND PIANO] buttons, press one

of the F#2–F#3 keys to set the desired amount of transposition.

To transpose the pitch down (in semitone steps)

While holding down the [SONG

] and [GRAND PIANO] buttons, press any

key between F#2 and B2.

To transpose the pitch up (in semitone steps)

While holding down the [SONG

] and [GRAND PIANO] buttons, press any

key between C#3 and F#3.

To restore the normal pitch

While holding down the [SONG

] and [GRAND PIANO] buttons, press the

C3 key.

Fine tuning of the Pitch

You can ﬁne tune the pitch of the entire instrument. This function is useful when you play the NP-

30/YNP-25 along with other instruments or CD music.

Setting the Pitch

To raise the pitch

in about 1cent steps (100 cents

= 1 semitone):

Hold down the E0, F0 and G0

keys simultaneously and press any

key between C3 and B3.

To lower the pitch

in about 1cent steps (100 cents

= 1 semitone):

Hold down the E0, F0 and F#0

keys simultaneously and press any

key between C3 and B3.

To restore standard pitch:

Hold down the E0, F0, F#0 and

G0 keys simultaneously and press

any key between C3 and B3.

TERMINOLOGY

Transpose:

Changing the key signature. On

the NP-30/YNP-25, transposing

shifts the pitch of the entire key-

board.

Transposition range:

F#2 (-6 semitones)–

C3 (normal pitch)–

F#3 (+6 semitones)

NOTE

C1 C2

0-1

-2 +1 +3-4

-3-5 +2 +4 +5

-6 +6

F#3F#2

Setting range: -65–+65 cents

The default setting (0 cent) is

A3=440Hz. In the 440Hz region,

1Hz=approximately 4 cents.

Pressing the key 8 times for

example, will set A3 at approxi-

mately 442Hz.

TERMINOLOGY

Default setting:

The “Default setting” refers to the

factory setting obtained when you

ﬁrst turn on the power to the NP-

30/YNP-25.

NOTE

C1 C2 C3 B3G0E0

C1E0

C2 C3 B3

F#0

C1G0E0

C2 C3 B3

F#0

Selecting & Playing Voices

NP-30/YNP-25 Owner’s Manual

Touch Sensitivity

You can adjust the volume level that changes depending on how fast or strong you hit the keys.

The following four settings are available.

Setting the Touch Sensitivity Type

While holding down the [GRAND PIANO] button, press one of the A5–C6 keys

to select the desired touch sensitivity.

KeyTouch Sensitivity Description

A5 FIXED The volume level does not change at all regardless of whether you play

the keyboard soft or hard.

A#5 SOFT The volume level does not change much when you play the keyboard soft

or hard.

B5 MEDIUM This is the standard piano touch response (default setting).

C6 HARD The volume level changes very widely from pianissimo to fortissimo to

facilitate dynamic and dramatic expression. You have to hit the keys hard

to produce a loud sound.

The touch sensitivity settings may

have little or no effect with Church

Organ 1, 2 and Harpsichord 1, 2

voices that are not normally

responsive to keyboard dynam-

ics.

Default setting: B5

NOTE

A5 C6

Connecting MIDI Instruments

NP-30/YNP-25 Owner’s Manual

Connecting MIDI Instruments

The NP-30/YNP-25 features MIDI IN/OUT terminals, allowing you to connect the NP-30/YNP-25 to

other instruments and devices—including computers—and take advantage of the various perfor-

mance and recording capabilities in MIDI applications.

Connecting MIDI [IN] [OUT] terminals

MIDI [IN] [OUT] terminals

Use MIDI cables to connect external MIDI devices to these

connectors.

About MIDI

MIDI (Musical Instrument Digital Interface) is a standard format for data transmis-

sion/reception. It enables the transfer of performance data and commands between

MIDI devices and personal computers. Using MIDI, you can control a connected MIDI

device from the NP-30/YNP-25, or control the NP-30/YNP-25 from a connected MIDI

device or computer.

MIDI’s Capability

MIDI functions enable you to transfer performance data between MIDI devices.

CAUTION

Before connecting the instrument to other electronic components, turn off the power of all the

components.

● Transferring performance data to and from another

MIDI device

● Transferring MIDI data to and from a computer

Since MIDI data that can be

transmitted or received varies

depending on the type of MIDI

device, check the “MIDI Imple-

mentation Chart” to ﬁnd out what

MIDI data and commands your

devices can transmit or receive.

The MIDI Implementation Chart

appears on

page 32

NOTE

You cannot transmit the voice

demo songs and the piano preset

songs from the NP-30/YNP-25 to

another MIDI device.

For MIDI connections, use a stan-

dard (optional) MIDI cable, avail-

able at most musical instrument

stores.

NOTE

Instrument

MIDI [OUT] terminal

MIDI cables

(optional)

MIDI [IN] terminal MIDI [OUT] terminal MIDI [IN] terminal

MIDI device

Instrument

Computer

USB terminal

USB-MIDI

interface

(optional)

MIDI [OUT]

terminal

MIDI [IN]

terminal

Connecting MIDI Instruments

NP-30/YNP-25 Owner’s Manual

Connecting a Personal Computer

By connecting a computer to the MIDI terminals, you can transfer data between the NP-30/YNP-25

and the computer via MIDI.

CAUTION

When connecting the NP-30/YNP-25 to a computer, ﬁrst turn off the power to both the NP-30/

YNP-25 and the computer before connecting any cables. After making connections, turn on the

power to the computer ﬁrst, then to the NP-30/YNP-25.

Connecting the USB port on the computer to the

NP-30/YNP-25 via an optional USB-MIDI interface

(such as the Yamaha UX16)

Use a USB-MIDI interface device to connect the USB port on your computer to the

NP-30’s/YNP-25’s MIDI terminals. You must install the USB-MIDI interface (such as

the UX16) driver. For more information, refer to the user’s manual that came with the

USB-MIDI interface device.

When the NP-30/YNP-25 is used

as a tone module, performance

data with voices that are not

found on the NP-30/YNP-25 will

not be played correctly.

NOTE

You must install a software appli-

cation on the computer to be able

to transfer MIDI data between the

NP-30/YNP-25 and a computer.

NOTE

Instrument

Computer

USB terminal

USB-MIDI

interface

(optional)

MIDI [OUT]

terminal

MIDI [IN]

terminal

MIDI Functions

NP-30/YNP-25 Owner’s Manual

MIDI Functions

You can make detailed adjustments to MIDI settings.

MIDI Transmit/Receive Channel Selection

In any MIDI control setup, the MIDI channels of the transmitting and

receiving devices must be matched for proper data transfer.

This parameter enables you to specify the channel on which the NP-

30/YNP-25 transmits or receives MIDI data.

Setting the Transmit Channel

While holding down the [SONG

] and [GRAND PIANO] buttons, press one

of the C1–E2 keys.

Setting the Receive Channel

While holding down the [SONG

] and [GRAND PIANO] buttons, press one

of the C4–F5 keys.

Local Control ON/OFF

“Local Control” refers to the fact that, normally, the NP-30/YNP-25 keyboard controls its internal

tone generator, allowing the internal voices to be played directly from the keyboard. This situation

is “Local Control On,” since the internal tone generator is controlled locally by its own keyboard.

Local control can be turned OFF, however, so that the NP-30/YNP-25 keyboard does not play the

internal voices, but the appropriate MIDI information is still transmitted via the MIDI OUT terminal

when notes are played on the keyboard. At the same time, the internal tone generator responds to

MIDI information received via the MIDI IN terminal.

While holding down the [SONG

] and [GRAND PIANO] buttons, press the

C6 key. Pressing the C6 key repeatedly toggles between Local Control On and

Off.

In Dual, Voice 1 data is transmit-

ted on its speciﬁed channel and

Voice 2 data is transmitted on the

next greater channel number rela-

tive to the speciﬁed channel. In

this case, no data is transmitted if

the transmit channel is set to

“OFF.”

ALL:

“Multi-timbre” Receive. This

allows simultaneous reception of

different parts on all 16 MIDI

channels, enabling the NP-30/

YNP-25 to play multi-channel

song data received from a music

computer or sequencer.

1+2:

“1+2” Receive. This allows simul-

taneous reception on channels 1

and 2 only, enabling the NP-30/

YNP-25 to play 1 and 2 channel

song data received from a music

computer or sequencer.

Program change and other like

channel messages received will

not affect the NP-30’s/YNP-25’s

panel settings or the notes you

play on the keyboard.

Data for the demo song and

piano preset songs cannot be

transmitted via MIDI.

NOTE

C1 C4

E2 F5

11 14 169

56810121315

OFF

742 11 14 169

56810121315

1+2

ALL

742

Transmit Channel

(C1–E2)

Receive Channel

(C4–F5)

Default setting: ON

MIDI Functions

NP-30/YNP-25 Owner’s Manual

Program Change ON/OFF

Normally the NP-30/YNP-25 will respond to MIDI program change numbers received from an

external keyboard or other MIDI device, causing the same numbered voice to be selected on the

corresponding channel (the keyboard voice does not change). The NP-30/YNP-25 will normally

also send a MIDI program change number whenever one of its voices is selected, causing the same

numbered voice or program to be selected on the external MIDI device if the device is set up to

receive and respond to MIDI program change numbers. This function makes it possible to cancel

program change number reception and transmission so that voices can be selected on the NP-30/

YNP-25 without affecting the external MIDI device.

While holding down the [SONG

] and [GRAND PIANO] buttons, press the

C#6 key. Pressing the C#6 key repeatedly toggles between Program Change On

and Off.

Control Change ON/OFF

Normally the NP-30/YNP-25 will respond to MIDI control change data received from an external

MIDI device or keyboard, causing the voice on the corresponding channel to be affected by pedal

and other “control” settings received from the controlling device (the keyboard voice is not

affected). The NP-30/YNP-25 also transmits MIDI control change information when the pedal or

other appropriate controls are operated.

This function makes it possible to cancel control change data reception and transmission so that,

for example, the NP-30’s/YNP-25’s pedal and other controls can be operated without affecting an

external MIDI device.

While holding down the [SONG

] and [GRAND PIANO] buttons, press the

D6 key. Pressing the D6 key repeatedly toggles between Control Change On and

Off.

For information on program

change numbers for each of the

NP-30’s/YNP-25’s voices, refer to

MIDI Data Format on page 28.

Default setting: ON

NOTE

C#6

For information on control

changes that can be used with

the NP-30/YNP-25, refer to MIDI

Data Format on page 28.

Default setting: ON

NOTE

Troubleshooting

NP-30/YNP-25 Owner’s Manual

Troubleshooting

Optional Equipment

Foot Pedal (FC3/FC4/FC5)

Keyboard Stand (L-2C)

USB-MIDI interface (UX16 )

Headphones (HPE-150/HPE-30)

Problem Possible Cause and Solution

The NP-30/YNP-25 does not turn on. The NP-30/YNP-25 has not been plugged in properly. Securely insert the female plug

into the jack on the NP-30/YNP-25, and the male plug into a proper AC outlet

(page 11).

The batteries are low or dead. Replace all six batteries with completely new alkaline

ones, or use the optional AC adaptor.

Noise is heard from the speakers or head-

phones.

The noise may be due to interference caused by the use of a mobile phone in close

proximity to the NP-30/YNP-25. Turn off the mobile phone, or use it further away from

the NP-30/YNP-25.

The batteries are low or dead. Replace all six batteries with completely new alkaline

ones, or use the optional AC adaptor.

The overall volume is low, or no sound is

heard.

The Master Volume is set too low; set it to an appropriate level using the [MASTER

VOLUME] control.

Make sure a pair of headphones is not connected to the headphones jack (page 13).

Make sure that Local Control (page 25) is ON.

The batteries are low or dead. Replace all six batteries with completely new alkaline

ones, or use the optional AC adaptor.

The sound is distorted. If you are using manganese batteries with the instrument, try replacing them with a

set of new alkaline batteries. Alternately, you could use the AC adaptor instead, or

try turning down the volume.

The sustain pedal has no effect. The pedal cable/plug may not be properly connected. Make sure to securely insert

the pedal plug into the SUSTAIN jack (page 13).

NP-30/YNP-25 Owner’s Manual

MIDI Data Format

If you’re already very familiar with MIDI, or are using a computer to control your music hardware with computer-generated MIDI

messages, the data provided in this section can help you to control the NP-30/YNP-25.

1. NOTE ON/OFF

Data format: [9nH] -> [kk] -> [vv]

9nH = Note ON/OFF event (n = channel number)

kk = Note number (Transmit: 09H–78H = A-2–C8 /

Receive: 00H–7FH = C-2–G8)

vv = Velocity (Key ON = 01H–7FH, Key OFF = 00H)

Data format: [8nH] -> [kk] -> [vv] (reception only)

8nH = Note OFF event (n = channel number)

kk = Note number: 00H–7FH = C-2–G8)

vv = Velocity

2. CONTROL CHANGE

Data format: [BnH] -> [cc] -> [vv]

BnH = Control change (n = channel number)

cc = Control number

vv = Data Range

(1) Bank Select

ccH Parameter Data Range (vvH)

00H Bank Select MSB 00H:Normal

20H Bank Select LSB 00H...7FH

Bank selection processing does not occur until receipt of next

Program Change message.

(2) Main Volume

ccH Parameter Data Range (vvH)

07H Volume MSB 00H...7FH

(3) Expression (reception only)

ccH Parameter Data Range (vvH)

0BH Expression MSB 00H...7FH

(4) Sustain

ccH Parameter Data Range (vvH)

40H Sustain MSB 00H...7FH

(5) Sostenuto (reception only)

ccH Parameter Data Range (vvH)

42H Sostenuto 00H...3FH:off, 40H...7FH:on

(6) Soft Pedal (reception only)

ccH Parameter Data Range (vvH)

43H Soft Pedal 00H...3FH:off, 40H...7FH:on

(7) Effect1 Depth (Reverb Send Level)

ccH Parameter Data Range (vvH)

5BH Effect1 Depth 00H...7FH

Adjusts the reverb send level.

(8) Effect4 Depth (Variation Effect Send Level)

ccH Parameter Data Range (vvH)

5EH Effect4 Depth 00H...7FH

(9) RPN

65H RPN MSB

64H RPN LSB

06H Data Entry MSB

26H Data Entry LSB

60H Data Increment

61H Data Decrement

* Parameters that are controllable with RPN:

• Coarse Tune

• Fine Tune

• Pitch Bend Range

3. MODE MESSAGES

Data format: [BnH] -> [cc] -> [vv]

BnH = Control event (n = channel number)

cc = Control number

vv = Data Range

(1) All Sound Off

ccH Parameter Data Range (vvH)

78H All Sound Off 00H

(2) Reset All Controllers

ccH Parameter Data Range (vvH)

79H Reset All Controllers 00H

Resets controllers as follows.

Controller Value

Expression 127 (max)

Sustain Pedal 0 (off)

Sostenuto 0 (off)

Soft Pedal 0 (off)

(3) Local Control (reception only)

ccH Parameter Data Range (vvH)

7AH Local Control 00H (off), 7FH (on)

(4) All Notes Off

ccH Parameter Data Range (vvH)

7BH All Notes Off 00H

Switches OFF all the notes that are currently ON on the spec-

iﬁed channel. Any notes being held by the sustain or soste-

nuto pedal will continue to sound until the pedal is released.

(5) Omni Off (reception only)

ccH Parameter Data Range (vvH)

7CH Omni Off 00H

Same processing as for All Notes Off.

(6) Omni On (reception only)

ccH Parameter Data Range (vvH)

7DH Omni On 00H

Same processing as for All Notes Off.

(7) Mono (reception only)

ccH Parameter Data Range (vvH)

7EH Mono 00H

Same processing as for All Sound Off.

(8) Poly (reception only)

ccH Parameter Data Range (vvH)

7FH Poly 00H

Same processing as for All Sound Off.

• When Control Change is turned OFF, Control Change mes-

sages will not be transmitted or received.

• Local on/off, OMNI on/off are not transmitted. (The appropriate

note off number is supplied with “All Note Off” transmission).

• When a voice bank MSB/LSB is received, the number is

stored in the internal buffer regardless of the received order,

then the stored value is used to select the appropriate voice

when a program change message is received.

•Poly mode is always active. This mode will not change when

the instrument receives a MONO/POLY mode message.

Appendix

NP-30/YNP-25 Owner’s Manual

4. PROGRAM CHANGE

Data format: [CnH] -> [ppH]

CnH = Program event (n = channel number)

ppH = Program change number

P. C . #=Program Change number

• When program change reception is turned OFF, no program

change data is transmitted or received.

• When you specify a program change as a number in the

range of 0–127, specify a number that is one less than the

program change number listed above. For example, to specify

program change number 1, you would specify a value of 0.

5. Pitch Bend Change (reception only)

[EnH] -> [ccH] -> [ddH]

ccH = LSB

ddH = MSB

6. SYSTEM REALTIME MESSAGES

[rrH]

F8H: Timing clock

FAH: Start

FCH: Stop

FEH: Active sensing

• If an error occurs during MIDI reception, the Sustain, Soste-

nuto, and Soft effects for all channels are turned off and an All

Note Off occurs.

7. SYSTEM EXCLUSIVE MESSAGES

(Universal System Exclusive)

(1) Universal Realtime Message

Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] ->

[llH] -> [mmH] -> [F7H]

MIDI Master Volume

• Simultaneously changes the volume of all channels.

• When a MIDI master volume message is received, the volume

only has affect on the MIDI receive channel, not the panel

master volume.

F0H = Exclusive status

7FH = Universal Realtime

7FH = ID of target device

04H = Sub-ID #1=Device Control Message

01H = Sub-ID #2=Master Volume

llH = Volume LSB

mmH =

Volume MSB

F7H = End of Exclusive

F0H = Exclusive status

7FH = Universal Realtime

XnH = When received, n=0–F.

X = irrelevant

04H = Sub-ID #1=Device Control Message

01H = Sub-ID #2=Master Volume

llH = Volume LSB

mmH =

Volume MSB

F7H = End of Exclusive

(2) Universal Non-Realtime Message (GM On)

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->

[F7H]

F0H = Exclusive status

7EH = Universal Non-Realtime

7FH = ID of target device

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

F0H = Exclusive status

7EH = Universal Non-Realtime

XnH = When received, n=0–F.

X = irrelevant

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

When the General MIDI mode ON message is received, the

MIDI system will be reset to its default settings.

This message requires approximately 50ms to execute, so

sufﬁcient time should be allowed before the next message is

sent.

NP-30/YNP-25 MSB LSB

P.C.##

Grand Piano 1 0 122 1

Grand Piano 2 0 112 1

E. Piano 1 0 122 6

E. Piano 2 0 122 5

Church Organ 1 0 123 20

Church Organ 2 0 122 20

Strings 0 122 49

Harpsichord 1 0 122 7

Harpsichord 2 0 123 7

Vibraphone 0 122 12

Data Transmission Reception

F8H

Transmitted every

96 clocks

Received as 96-clock tempo timing

when MIDI clock is set to External.

FAH Song start

Song start

Not received when the MIDI clock is

set to Internal.

FCH Song stop

Song stop

Not received when the MIDI clock is

set to Internal.

FEH

Transmitted every

200 milliseconds

If a signal is not received via MIDI for

more than 400 milliseconds, the

same processing will take place for All

Sound Off, All Notes Off and Reset All

Controllers as when those signals are

received.

NP-30/YNP-25 Owner’s Manual

8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->

[mmH] -> [llH] -> [ddH] -> [F7H]

F0H = Exclusive status

43H = YAMAHA ID

1nH = When received, n=0–F.

When transmitted, n=0.

4CH = Model ID of XG

hhH = Address High

mmH =

Address Mid

llH = Address Low

ddH = Data

F7H = End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI sys-

tem will be reset to its default settings.

The message requires approximately 50ms to execute, so

sufﬁcient time should be allowed before the next message is

sent.

(2) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

[bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->...->

[ccH] -> [F7H]

F0H = Exclusive status

43H = YAMAHA ID

0nH = When received, n=0–F.

When transmitted, n=0.

4CH = Model ID of XG

aaH = ByteCount

bbH = ByteCount

hhH = Address High

mmH =

Address Mid

llH = Address Low

ddH = Data

| |

ccH = Check sum

F7H = End of Exclusive

• Receipt of the XG SYSTEM ON message causes reinitializa-

tion of relevant parameters and Control Change values. Allow

sufﬁcient time for processing to execute (about 50 msec)

before sending the NP-30/YNP-25 another message.

• XG Native Parameter Change message may contain two or

four bytes of parameter data (depending on the parameter

size).

•For information about the Address and Byte Count values,

refer to Table 1 below. Note that the table’s Total Size value

gives the size of a bulk block. Only the top address of the

block (00H, 00H, 00H) is valid as a bulk data address.

9. SYSTEM EXCLUSIVE MESSAGES

(Digital Piano MIDI Format)

Data format:

[F0H] -> [43H] -> [73H] -> [01H] -> [nnH] -> [F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Digital Piano ID

01H = Product ID (digital piano common)

nnH = Substatus

02H Internal MIDI clock

03H External MIDI clock

F7H = End of Exclusive

10.

SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [7FH] -> [4BH] ->

[11H] -> [0nH] -> [ccH] -> [vvH] -> [F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Digital Piano ID

7FH = Extended Product ID

4BH = Product ID

11H = Special control

0nH = Control MIDI change (n=channel number)

cc = Control number

vv = Value

F7H = End of Exclusive

Control Channel ccH vvH

Channel Detune

ch: 00H–0FH 43H (Sets the Detune value

for each channel)

00H–7FH

Voice Reserve

ch: 00H–0FH 45H 00H : Reserve off 7FH

: on*

When Volume, Expression is received for Reserve On, they

will be effective from the next Key On. Reserve Off is normal.

11. SYSTEM EXCLUSIVE MESSAGES (Others)

Data format:

[F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]

-> [00H] -> [mmH] -> [

H] -> [ccH] -> [F7H]

Master Tuning (XG and last message priority) simultaneously

changes the pitch of all channels.

F0H = Exclusive Status

43H = Yamaha ID

1nH = When received, n=0–F.

When transmitted, n=0.

27H = Model ID of TG100

30H = Sub ID

00H =

mmH = Master Tune MSB

llH = Master Tune LSB

ccH = irrelevant (under 7FH)

F7H = End of Exclusive

NP-30/YNP-25 Owner’s Manual

MIDI Parameter Change table (SYSTEM)

Address (H) Size (H) Data (H) Parameter Description Default value (H)

00 00 00 4 020C–05F4(*1) MASTER TUNE -50–+50[cent] 00 04 00 00

01 1st bit 3–0 ➝ bit 15–12 400

02 2nd bit 3–0 ➝ bit 11–8

03 3rd bit 3–0 ➝ bit 7–4

4th bit 3–0 ➝ bit 3–0

04 1 00–7F MASTER VOLUME 0–127 7F

7E 00 XG SYSTEM ON 00=XG sytem ON

7F 00 RESET ALL PARAMETERS 00=ON (receive only)

TOTAL SIZE 07

*1: Values lower than 020CH select -50 cents. Values higher than 05F4H select +50 cents.

MIDI Parameter Change table (EFFECT 1)

Refer to the “Effect MIDI Map” for a complete list of Reverb, Chorus and Variation type numbers.

Address (H) Size (H) Data (H) Parameter Description Default value (H)

02 01 00 2 00–7F REVERB TYPE MSB Refer to Effect MIDI Map 01 (=HALL1)

00–7F REVERB TYPE LSB 00 : basic type 00

02 01 40 2 00–7F VARIATION TYPE MSB Refer to Effect MIDI Map 00 (=Effect off)

00–7F VARIATION TYPE LSB 00 : basic type 00

• “VARIATION” refers to the EFFECT on the panel.

MIDI Parameter Change table (MULTI PART)

Address (H) Size (H) Data (H) Parameter Description Default value (H)

08 nn 11 1 00–7F DRY LEVEL 0–127 7F

nn = Part Number

• Effect MIDI Map

REVERB

MSB LSB

ROOM 02H 10H

HALL 1 01H 10H

HALL 2 01H 11H

STAGE 03H 10H

OFF 00H 00H

EFFECT

MSB LSB

CHORUS 42H 10H

PHASER 48H 10H

TREMOLO 46H 10H

ROTARY SP 47H 10H

OFF 00H 00H

NP-30/YNP-25 Owner’s Manual

MIDI Implementation Chart

TransmittedFunction Recognized Remarks

Basic

Channel

Note

Number : True voice

Velocity

After

Touch

Pitch Bend

Control

Change

Mode

Default

Changed

Note ON

Note OFF

Key's

Ch's

0,32

6,38

66,67

91,94

96-97

100-101

1 - 16

Ø 9nH,v=1-127

**************

0 - 127

**************

˛ Ø 0 - 24 semi

1 - 16

Ø 9nH,v=1-127

0 - 127

Default

Messages

Altered

YAMAHA [ Digital Keyboard ] Date : 18-JAN-2007

Model NP-30/NP-30S/YNP-25 MIDI Implementation Chart

Version : 1.0

Bank Select

Modulation

Main Volume

Panpot

Expression

Data Entry

Sustain

Portamento Control

Effect Depth

RPN Inc,Dec

RPN LSB,MSB

NP-30/YNP-25 Owner’s Manual

Prog

Change : True #

System Exclusive

Common : Song Pos.

: Song Sel.

: Tune

System : Clock

Real Time : Commands

: All Sound Off

Aux :

Reset

All

Cntrls

: Local ON/OFF

Mes- : All Notes OFF

sages: Active Sense

: Reset

Notes:

Ø 0 - 127

**************

Mode 1 : OMNI ON , POLY Mode 2 : OMNI ON ,MONO

Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF,MONO

Ø (120,126,127)

Ø (121)

Ø (122)

Ø (123-125)

Ø : Yes

˛ : No

Ø 0 - 127

NP-30/YNP-25 Owner’s Manual

Speciﬁcations

•When an optional FC3 Foot Pedal is connected, the half pedal effect can be used.

•Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change

or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations, equipment or options may not be the

same in every locale, please check with your Yamaha dealer.

Keyboard 76 keys (Graded Touch)

Sound Source AWM Stereo Sampling

Polyphony (Max.) 32

Voice Selection 10

Effect Reverb

Volume Master Volume

Controls Dual, Metronome, Transpose, Tuning, Touch (Hard/Medium/Soft/Fixed)

Pedal SUSTAIN PEDAL*

Demo Songs 10 Voice Demo Songs, 10 Piano Preset Songs

MIDI

Local On/Off, Transmit/Recieve channel, Program change On/Off,

Control change On/Off

Jacks/Connectors MIDI (IN/OUT), PHONES/OUTPUT, DC IN 12V, SUSTAIN

Main Ampliﬁers 6 W + 6 W

Speakers (12 cm × 6 cm) × 2

Dimensions (W × D × H) 1,244mm × 259mm × 100mm [49" × 10-1/4" × 4"]

Weight 5.4 kg (11 lbs., 14 oz.)

Power Supply

Adaptor: PA-5D, PA-150, or an equivalent recommended by Yamaha

Batteries: Six AA size, LR-6 or equivalent

Power Consumption 20 W

Accessories Owner’s Manual, Music Rest

Index

NP-30/YNP-25 Owner’s Manual

Index

Combining Voices (Dual)...............................................19

Connecting a Personal Computer..................................24

DC IN 12V.......................................................................11

Default setting .................................................................21

Demo Songs.....................................................................14

Dual..................................................................................19

[GRAND PIANO] button.............................18, 19, 20, 22

[MASTER VOLUME] slider...........................................13

Metronome......................................................................16

MIDI [IN] [OUT] ...........................................................23

MIDI Data Format ..........................................................28

MIDI Implementation Chart..........................................32

MIDI terminals................................................................23

Music Rest........................................................................13

Optional Equipment .......................................................27

Panel Controls and Terminals........................................10

[PHONES/OUTPUT] jack .............................................13

Piano Preset Songs ..........................................................15

PRECAUTIONS ............................................................4, 5

Preset songs ➝ Piano Preset Songs ................................15

Reverb ..............................................................................20

Song .................................................................................15

[SONG

] button .................................................. 14, 15

Specifications...................................................................34

[STANDBY/ON] switch .................................................12

Start/stop playback.......................................................... 15

Demo songs ............................................................... 14

Piano Preset Song......................................................15

[SUSTAIN] jack ..............................................................13

Touch Sensitivity.............................................................22

Transposition ..................................................................21

Troubleshooting.............................................................. 27

Tuning ➝Fine tuning of the Pitch.................................21

Voice ................................................................................ 18

VOICE/SONG [BACK<<], [>>NEXT] button

........................................................................... 14, 15, 18

NP-30/YNP-25 Owner’s Manual

Memo

NP-30/YNP-25 Owner’s Manual

Memo

NP-30/YNP-25 Owner’s Manual

Limited Warranty

90 DAYS LABOR 1 YEAR PARTS

Yamaha Corporation of America, hereafter referred to as Yamaha, warrants to the original consumer of a product included in the categories listed

below, that the product will be free of defects in materials and/or workmanship for the periods indicated. This warranty is applicable to all models

included in the following series of products:

NP, YNP SERIES OF DIGITAL KEYBOARDS

If during the ﬁrst 90 days that immediately follows the purchase date, your new Yamaha product covered by this warranty is found to have a defect

in material and/or workmanship, Yamaha and/or its authorized representative will repair such defect without charge for parts or labor.

If parts should be required after this 90 day period but within the one year period that immediately follows the purchase date, Yamaha will, subject

to the terms of this warranty, supply these parts without charge. However, charges for labor, and/or any miscellaneous expenses incurred are the

consumers responsibility. Yamaha reserves the right to utilize reconditioned parts in repairing these products and/or to use reconditioned units as

warranty replacements.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY WHICH YAMAHA MAKES IN CONNECTION WITH THESE PRODUCTS. ANY

IMPLIED WARRANTY APPLICABLE TO THE PRODUCT, INCLUDING THE WARRANTY OF MERCHANT ABILITY IS LIMITED TO

THE DURATION OF THE EXPRESS WARRANTY. YAMAHA EXCLUDES AND SHALL NOT BE LIABLE IN ANY EVENT FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow limitations that relate to implied warranties and/or the exclusion of incidental or consequential damages. Therefore, these

limitations and exclusions may not apply to you.

This warranty gives you speciﬁc legal rights. You may also have other rights which vary from state to state.

CONSUMERS RESPONSIBILITIES

If warranty service should be required, it is necessary that the consumer assume certain responsibilities:

1. Contact the Customer Service Department of the retailer selling the product, or any retail outlet authorized by Yamaha to sell the product for

assistance. You may also contact Yamaha directly at the address provided below.

2. Deliver the unit to be serviced under warranty to: the retailer selling the product, an authorized service center, or to Yamaha with an explanation

of the problem. Please be prepared to provide proof purchase date (sales receipt, credit card copy, etc.) when requesting service and/or parts

under warranty.

3. Shipping and/or insurance costs are the consumers responsibility.* Units shipped for service should be packed securely.

*Repaired units will be returned PREPAID if warranty service is required within the ﬁrst 90 days.

IMPORTANT: Do NOT ship anything to ANY location without prior authorization. A Return Authorization (RA) will be issued that has

a tracking number assigned that will expedite the servicing of your unit and provide a tracking system if needed.

4. Your owners manual contains important safety and operating instructions. It is your responsibility to be aware of the contents of this manual and

to follow all safety precautions.

EXCLUSIONS

This warranty does not apply to units whose trade name, trademark, and/or ID numbers have been altered, defaced, exchanged removed, or to

failures and/or damages that may occur as a result of:

1. Neglect, abuse, abnormal strain, modiﬁcation or exposure to extremes in temperature or humidity.

2. Improper repair or maintenance by any person who is not a service representative of a retail outlet authorized by Yamaha to sell the product, an

authorized service center, or an authorized service representative of Yamaha.

3. This warranty is applicable only to units sold by retailers authorized by Yamaha to sell these products in the U.S.A., the District of Columbia,

and Puerto Rico. This warranty is not applicable in other possessions or territories of the U.S.A. or in any other country.

Please record the model and serial number of the product you have purchased in the spaces provided below.

Model___________________________ Serial #________________________________ Sales Slip #________________________________

Purchased from____________________________________________________________ Date______________________________________

(Retailer)

YAMAHA CORPORATION OF AMERICA

Electronic Service Division

6600 Orangethorpe Avenue

Buena Park, CA 90620

KEEP THIS DOCUMENT FOR YOUR RECORDS. DO NOT MAIL!

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

CEP 04534-013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,

Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH,

Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Central Europe GmbH,

Branch Austria, CEE Department

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Central Europe GmbH

Sp.z. o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,

Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha-Hazen Música, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 6A

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

25/F., United Plaza, 1468 Nanjing Road (West),

Jingan, Shanghai, China

Tel: 021-6247-2211

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 080-004-0022

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

891/1 Siam Motors Building, 15-16 ﬂoor

Rama 1 road, Wangmai, Pathumwan

Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-3273

[PK] 40

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

WJ15960 004POXXXX.X-XXB0

Printed in China

Yamaha Home Keyboards Home Page (English Only)

http://music.yamaha.com/homekeyboard

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha NP-30 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha NP-30

Yamaha NP-30 User Manual - German - 38 pages

Yamaha NP-30 User Manual - Dutch - 37 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yamaha NP-30 Manual

Product: