571303
62
Zoom out
Zoom in
Previous page
1/76
Next page
62
MOX6/MOX8 Owner’s Manual
Appendix
Troubleshooting
No sound? Wrong sound? When a problem like this occurs, please check the following points before assuming that the product
is faulty. Many problems can be solved by executing the Factory Set operation (page 19), after backing up your data to an USB
flash memory device (page 57). If the problem persists, consult your Yamaha dealer.
No Sound.
Is this instrument properly connected to related external equipment (e.g., amplifier, speaker, headphone) via audio cables?
Since this instrument has no built-in speakers, you will need an external audio system or a set of stereo headphones to properly
monitor it (page 17).
Is the power of this synthesizer and any external equipment connected to it turned on?
Have you made all the appropriate level settings—including the Master Volume on this instrument and the volume settings on any
connected external equipment?
If the Foot Controller is connected to the [FOOT CONTROLLER] jack, operate the Foot Controller and check the sound volume.
Check the Local Control parameter in the Utility mode.
When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard.
Check the Direct Monitor Switch parameter in the Utility mode.
When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard.
When the Performance/Song/Pattern produces no sound, is the “ArpPlyOnly” parameter of each Part turned on?
When this parameter is turned on, the corresponding Part produces sound only via Arpeggio playback.
Are the MIDI volume or MIDI expression settings too low when using the external controller?
Are the effect and filter settings appropriate?
If you are using the filter, try changing the cutoff frequency. Some cutoff settings may filter out all of the sound.
Is “Vocoder” selected as the Insertion Effect Type of the Voice?
If so, set the parameters related to the AD Part and A/D INPUT connector to the appropriate values then play the keyboard while
speaking into the connected microphone. Check whether or not the A/D INPUT [GAIN] Knob on the rear panel is set to the minimum
position.
Are the volume or expression settings too low?
Are the parameter settings such as Element Switch, Part Switch, Note Limit and Velocity Limit appropriate?
[UTILITY] [F6] MIDI [SF2] SWITCH “LocalCtrl”
[UTILITY] [F5] USB I/O “DirectMonitorSw Part”
[PERFORM] [EDIT] Number [1] – [4] [F1] VOICE [SF2] MODE “ArpPlyOnly?
[SONG]/[PATTERN] [MIXING] [EDIT] Number [1] – [16] [F1] VOICE [SF2] MODE “ArpPlyOnly
[VOICE] [F6] EFFECT
[PERFORM] [F6] EFFECT
[SONG]/[PATTERN] [MIXING] [F6] EFFECT
[VOICE] [EDIT] Element/Key selection [F3] FILTER
[PERFORM] [EDIT] Part selection [F4] TONE [SF1] FILTER
[SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F4] TONE [SF1] FILTER
[SONG]/[PATTERN] [UTILITY] [F2] SEQ [SF2] FILTER
[VOICE] [F6] EFFECT [SF1] CONNECT “InsEF Connect”
[UTILITY] [F1] GENERAL [SF1] TG “Volume”
[VOICE] [EDIT] [COMMON] [F2] OUTPUT “Volume”
[VOICE] [EDIT] Element/Key selection [F4] AMP [SF1] LVL/PAN “Level”
[PERFORM] [EDIT] [COMMON] [F2] OUT/MFX [SF1] OUT “Volume
[PERFORM] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN “Volume
[SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN “Volume
[VOICE] [EDIT] Element/Key selection [F1] OSC [SF1] WAVE “ElementSw”
[VOICE] [EDIT] Element/Key selection [F1] OSC [SF3] LIMIT
[PERFORM] [F2] VOICE
[PERFORM] [EDIT] Part selection [F1] VOICE [SF1] VOICE “PartSw”
[PERFORM] [EDIT] Part selection [F1] VOICE [SF3] LIMIT
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MOX8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MOX8 in the language / languages: English as an attachment in your email.

The manual is 11,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha MOX8

Yamaha MOX8 User Manual - English - 48 pages

Yamaha MOX8 Installation Guide - English - 6 pages

Yamaha MOX8 Installation Guide - English - 6 pages

Yamaha MOX8 User Manual - English - 11 pages

Yamaha MOX8 User Manual - English - 12 pages

Yamaha MOX8 User Manual - German - 57 pages

Yamaha MOX8 User Manual - German - 48 pages

Yamaha MOX8 Installation Guide - German - 10 pages

Yamaha MOX8 Installation Guide - German - 6 pages

Yamaha MOX8 User Manual - German - 14 pages

Yamaha MOX8 User Manual - German - 6 pages

Yamaha MOX8 User Manual - German - 76 pages

Yamaha MOX8 User Manual - Dutch - 1 pages

Yamaha MOX8 User Manual - Dutch - 76 pages

Yamaha MOX8 User Manual - French - 57 pages

Yamaha MOX8 User Manual - French - 76 pages

Yamaha MOX8 Installation Guide - French - 10 pages

Yamaha MOX8 Installation Guide - French - 6 pages

Yamaha MOX8 Installation Guide - French - 6 pages

Yamaha MOX8 User Manual - Italian - 76 pages

Yamaha MOX8 User Manual - Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info