571289
277
Zoom out
Zoom in
Previous page
1/300
Next page
277
MOTIF Appendix
Display Messages
Appendix
Display Messages
Messages Information
MIDI buffer full. Failed to process the MIDI data because too much data was received at one time.
MIDI data error. An error occurred when receiving MIDI data.
MIDI checksum error. An error occurred when receiving bulk data.
Bulk protected. Bulk data or a SCSI message was received when RcvBulk was set to “protect.” (See page 258.)
Device number is off. Bulk data cannot be transmitted/received since the device number is off.
Device number mismatch. Bulk data cannot be transmitted/received since the device numbers don't match.
Change internal battery. The internal backup battery has no remaining power. Replace the battery.
Disk or card full.
The card or disk is full and no more data can be saved. Use a new card or disk, or make space by erasing unwanted data
from the card or disk.
File not found.
The specified file was not found on the card or disk during a load operation. Try again after re-inserting/re-connecting the
card or disk.
Bad disk or card. The card or disk is unusable. Format the card or disk and try again.
Disk or card not ready. A card or disk is not properly inserted in or connected to the MOTIF.
Disk or card unformatted. The card or disk is not formatted, or the format is unusable by the MOTIF. Check the card/disk contents.
Disk or card write protected. The card or disk is write protected, or you have attempted to write to a read-only medium such as CD-ROM.
Illegal disk or card. The format type of the SCSI disk or Memory card is wrong.
Illegal file. The file specified for loading is unusable by the MOTIF.
Illegal file name. The specified file name is unacceptable. Try entering a different name.
Read only file. You have attempted to delete, rename, or overwrite a read-only file.
Can't make folder. No more directories can be created below the current level.
Folder is too deep. Directories below this level cannot be accessed.
Unknown file format. The file format type is not supported by the MOTIF.
SCSI error. A SCSI error has occurred. Check the SCSI connections and termination.
Disk or card read/write error. An error occurred while reading or writing to/from SCSI disk or Memory card.
Can't find associated files. The file associated with the file to be loaded cannot be found.
Folder not empty You attempt to delete a folder that contains data.
Unsupported disk The disk (memory card or SCSI device connected to the MOTIF) is not supported by the MOTIF.
Seq memory full.
The internal memory for Sequence data is full. The internal memory for Sequence data is full, preventing any further
operation (such as recording, editing, Job execution, MIDI reception/transmission, or loading from Memory card or SCSI
drive). Try again after erasing unwanted song, pattern, or user phrase data.
Choose user phrase.
You have attempted to record a pattern track to which a preset phrase is assigned. If you wish to use a preset phrase as
a starting data for pattern recording, copy it to a user phrase before recording.
No data. When a Song/Pattern Job is executed, the selected track or range contains no data. Select an appropriate track or range.
Illegal check box.
No check boxes have been checked in a Sequencer track Job which requires a check box selection. Check the
appropriate check box.
No F7 (End of Exc.)
Exclusive data has been entered or changed without the necessary “End of Exclusive” byte (F7). Make sure F7 is
included.
Pattern length mismatch. A Pattern Job will result in the length of a Pattern being greater than 256 measures.
Phrase length mismatch A Pattern Job will result in the length of a phrase being greater than 256 measures.
Phrase number overflow The maximum number of phrases (256) has been exceeded when recording, executing a Pattern Job, or editing.
Illegal input. An unacceptable input or value has been specified. Check the input method or value.
Illegal track number. An unacceptable track number has been specified in the Song/Pattern mode. Select the track again.
Illegal phrase number. An unacceptable phrase number has been specified in the Pattern mode. Select the phrase again.
Illegal measure. An unacceptable measure number has been specified in the Song/Pattern mode. Select the measure again.
Meter mismatch In the Pattern Job mode, the meter (time signature) of the destination pattern is different from the meter of the source pattern.
Sample memory full. The sample memory is full and further sampling operations, Jobs, or load operations cannot be executed.
Too many samples. The maximum overall number of samples (8192) has been exceeded.
Sample is too short. The sample length is too short and the Frequency Convert Job cannot be executed.
Sample freq is too low. The sampling frequency is too low and the Frequency Convert Job cannot be executed.
Illegal sample data. The sample file specified for loading is unusable by the MOTIF.
No sample data. The linked sample files cannot be found during a load operation.
Sample is too long. The sample size is too large and the Time Stretch Job cannot be executed.
SIMM configuration error. An appropriate pair of expansion SIMMs is not properly installed, or the pair is not properly matched (page 287).
Multi plug-in is not in slot 3.
The Multi-Part Plug-in board does not work because it has not been installed to slot 3. The Multi-Part Plug-in board
should be installed to slot 3.
Effect plug-in is not in slot 1.
The Effect Plug-in board does not work because it has not been installed to slot 1. The Effect Plug-in board should be
installed to slot 1.
Plug-in 1 communication error. The Plug-in board that has been installed to slot 1 does not work.
Plug-in 2 communication error. The Plug-in board that has been installed to slot 2 does not work.
Plug-in 3 communication error. The Plug-in board that has been installed to slot 3 does not work.
277


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MOTIF8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MOTIF8 in the language / languages: English as an attachment in your email.

The manual is 10,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha MOTIF8

Yamaha MOTIF8 User Manual - English - 33 pages

Yamaha MOTIF8 Additional guide - English - 2 pages

Yamaha MOTIF8 Installation Guide - English - 44 pages

Yamaha MOTIF8 User Manual - German - 33 pages

Yamaha MOTIF8 Additional guide - German - 2 pages

Yamaha MOTIF8 Installation Guide - German - 44 pages

Yamaha MOTIF8 User Manual - German - 300 pages

Yamaha MOTIF8 User Manual - Dutch - 300 pages

Yamaha MOTIF8 User Manual - French - 33 pages

Yamaha MOTIF8 User Manual - French - 300 pages

Yamaha MOTIF8 Additional guide - French - 2 pages

Yamaha MOTIF8 Installation Guide - French - 44 pages

Yamaha MOTIF8 User Manual - Italian - 300 pages

Yamaha MOTIF8 User Manual - Spanish - 299 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info