618045
20
Zoom out
Zoom in
Previous page
1/28
Next page
Front & Rear Panels
MG32/14FX, MG24/14FX
20
MASTER I/O Section
1 RETURN Jacks (1, 2)
These are unbalanced phone input jacks. The signal into each
of these jacks feeds into the ST bus and into AUX buses 1 to 4.
These jacks are typically used to receive a return signal from an
external effector (reverb, delay, etc.).
These jacks can also be used as an auxiliary stereo
input. If you connect to the L (MONO) jack only, the
mixer will recognize the signal as monaural and will
propagate the identical signal from both L and R
jacks.
2 2TR IN Jacks
These unbalanced RCA-pin input jacks can be used to input a
stereo sound source. The signal into each of these jacks feeds
into the ST bus. Use these jacks when you want to connect a
stereo sound source (such as a CD player or DAT deck) directly
to the mixer for monitoring.
3 REC OUT (L, R) Jacks
These are unbalanced RCA-pin output jacks. By connecting
these jacks to an external recorder, you can record the same
signal that is being output from the ST OUT jacks.
The signal from these jacks is not adjusted by the
ST master fader and is not affected by input or out-
put at the INSERT I/O jacks. When using these
jacks to record, adjust the level as necessary at the
external recording device.
4 SEND Jacks
•AUX Jacks (1 to 6)
These are impedance-balanced phone jacks. These jacks out-
put the signals from AUX1 to AUX6, respectively. You use
these jacks, for example, to connect to a monitoring system,
effector, or other such equipment.
EFFECT Jacks (1, 2)
These impedance-balanced phone jacks output the signals
from the EFFECT buses. You would typically use these jacks
to connect to an external effector.
5 GROUP INS I/O Jacks (1 to 4)
These are unbalanced TRS (tip, ring, sleeve) phone-type bidi-
rectional jacks. You can use these jacks to connect individual
groups to devices such as graphic equalizers, compressors, and
noise filters.
Connection to an INSERT I/O jack requires a spe-
cial separately-sold insertion cable such as illus-
trated below.
6 GROUP OUT Jacks (1 to 4)
These are impedance-balanced phone output jacks. These jacks
output the signals from GROUP buses 1 to 4. Use these jacks to
connect to the input jacks of MTRs, external mixers, and other
such devices.
BA87 1
2345690C
NOTE
NOTE
NOTE
To the INSERT I/O jack
To the input jack of the external processor
To the output jack of the external processor
Ring
Sleeve
Tip
Sleeve
Tip
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MG24-14fx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MG24-14fx in the language / languages: English as an attachment in your email.

The manual is 6,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info