464214
19
Zoom out
Zoom in
Previous page
1/40
Next page
MG20XU/MG20/MG16XU/MG16/MG12XU/MG12 Owner’s Manual
19
Controls and Connectors
BAL: Sets the volume balance of the signal sent from
each stereo input channel (L/R) to the STEREO
L/R bus or GROUP bus. When this knob is set to
the 12 o’clock position, the sound of the stereo
input channels (L/R) will be sent to the STEREO
L/R bus or GROUP 1, 3/2, 4 bus at the same vol-
ume.
PAN/BAL: This knob performs both [PAN] and [BAL]
functions. You can use this as a [PAN] control
when sound is input to the [LINE] (L/MONO) jack,
and as a [BAL] control when sound is input to
both the [LINE] (L) and [LINE] (R) jacks.
!3 [ON] switches
Turn this switch on ( ) to send the respective channel’s
signal to the buses. The switch lights when on. When this
switch is off ( ), the respective signal input is not sent to
the AUX bus or GROUP bus.
NOTE
Even if the [ON] switch is off, the PFL signal from each chan-
nel can still be monitored via the [PHONES] jack.
To minimize noise, turn the [ON] switch off for any unused
channels.
!4 [PEAK] indicators
The peak level of the post-EQ signal is detected, and the
PEAK indicator lights red when the level reaches 3 dB below
clipping.
!5 Bus assign switch
These switches determine the bus(es) to which each channel’s
signal is sent. Turn the switch on ( ) to output the signal to
the corresponding buses.
[1-2] switch: Assigns the channel’s signal to the
GROUP 1-2 buses.
[3-4] switch: Assigns the channel’s signal to the
GROUP 3-4 buses.
[ST] switch: Assigns the channel’s signal to the STE-
REO L/R buses.
NOTE
To send the signal to each bus, engage the [ON] switch !3.
!6 [PFL] (Pre-fader Listen) switch
When the [PFL] switch is on ( ), the channel pre-fader
signal is output to the [MONITOR OUT] and [PHONES]
jacks for monitoring. In this condition, the audio from the
STEREO L/R buses or GROUP buses that could be heard in
the [MONITOR OUT] and [PHONES] jacks can no longer be
heard. When a [PFL] switch is turned on, the [PFL] indicator
below the level meter flashes.
!7 Channel faders
For adjusting the level of the channel signal. Use these con-
trols to adjust the balance between the various channels.
NOTE
To minimize noise, set the fader sliders for any unused chan-
nels all the way down.
STEREO L bus,
GROUP 1 bus,
GROUP 3 bus
STEREO R bus,
GROUP 2 bus,
GROUP 4 bus
BAL
LINE L
LINE R
MG20XU/MG20
MG16XU/MG16
MG12XU/MG12
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MG 16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MG 16 in the language / languages: English as an attachment in your email.

The manual is 5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha MG 16

Yamaha MG 16 User Manual - German - 40 pages

Yamaha MG 16 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info