557717

Yamaha MDX-E300 Manual

26
Zoom out
Zoom in
Previous page
1/184
Next page
24
ADDITIONAL INFORMATION
Troubleshooting
If your MD recorder fails to operate normally, check the following table. It lists common operating errors and simple
measures which you can take to correct the problem. If it cannot be corrected, or the symptom is not listed, disconnect the
recorder’s power cord and contact your authorized YAMAHA dealer or service center for help.
CAUSE
MD is dirty or damaged.
MD is damaged (“UTOC Err L0~4” appears in the
display).
There is an influence of strong external noise
(lightning, excessive static electricity, etc.) or a
misoperation was performed while using this unit.
Moisture is on the laser pickup.
The power is OFF.
The disc has been loaded incorrectly.
An unrecorded (blank) MD was loaded (“Blank
Disc” appears in the display).
The disc is write protected (“Protected” appears in
the display).
A pre-mastered MD is loaded (“PlayBack MD”
appears in the display).
The source is not connected correctly.
The input setting is incorrect.
The recording level is too low.
The digital output level of the digital source is too
low.
There is not enough blank space left on the MD.
If the power cord was unplugged or there was a
power outage during recording, that recording may
be lost.
The carriage lock function has activated.
The unit is too close to the television or other
component.
The batteries are exhausted.
The remote control transmitter is operated from an
incorrect distance or angle.
The remote control sensor is located in strong
direct light.
REMEDY
Replace the current disc with a new one.
Turn the power off and disconnect the AC power
from the AC outlet. After about 30 seconds have
passed, connect the power and try again.
Leave the unit switched ON and wait 20 to 30
minutes for the moisture to evaporate before
trying to play a disc.
Press STANDBY/ON (POWER on the remote
control) to turn the power on.
Reload the disc with the label side facing up, and
the arrow pointing toward the disc insertion slot.
Insert a recorded MD.
Slide the write-protect tab to the closed position.
Load a recordable MD.
Check all connections again.
Press INPUT repeatedly to select the correct
input jacks.
Turn REC LEVEL to adjust the recording level.
Set the digital output level of the digital source to
“MAX”.
Load a recordable MD with fewer recorded
tracks, or erase unnecessary tracks from the
current MD.
If recording was interrupted, try recording again
starting from the beginning.
Insert the MD completely, then press to eject
it.
Place the unit farther away from the television or
other component.
Replace the batteries.
Operate the remote from less than 6 meters
(about 20 feet) and within 30° on either side of
the sensor.
Place the unit away from the strong light.
SYMPTOM
The unit does not respond to operations.
The unit does not work normally.
Playback is not possible.
Recording is not possible.
The MD cannot be removed when
partially inserted.
Excessive noise.
The remote control does not operate.
0107MDXE300(M).21-25.E 02.5.17, 10:54 AM24
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MDX-E300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MDX-E300 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info