554952
51
Zoom out
Zoom in
Previous page
1/53
Next page
E-43
English
CD/Video CD player
Problem
A disc cannot be played
normally, or there is a noise
during play.
Play will not begin even if
disc is loaded.
No sound or no picture.
Sound stops suddenly
(always at the same spot).
A picture is disturbed or
unstable.
Tape will not move during
playback or recording.
Recording is not possible.
Sound is distorted or fades
out, or stereo balance is poor.
Poor sound quality.
Excessive noise.
Tape travel stops in middle of
playback or recording.
The beginning of desired
selections on tape cannot be
found.
Beginning of the track isn’t
recorded.
Remote control does not
work.
TV functions strangely when
the remote control is used.
Cause
The disc is not a standard type.
Disc is upside down.
Disc is dirty.
The input source selection is incorrect.
Disc is dirty.
Volume is set too high.
Setting of the TV MODE switch on the rear
panel is improper.
Slack tape wrapped around pinch roller.
Erasure prevention tab is broken off.
Head is dirty.
Head is dirty.
Tape is worn.
Tape encoded with Dolby NR is played back
with this system’s Dolby NR off.
Tape not encoded with Dolby NR is played
back with this system’s Dolby NR on.
Head has become magnetized.
Slack tape coming out of cassette shell.
Tape is creased or torn.
Endless tape is being used.
Silent gaps between selections are too short.
Excessively soft passages in middle of
selections.
Conversation, etc. is recorded.
There is an unrecordable part in the first few
seconds of the tape.
Batteries are dead.
Remote control is too far away or tilted too
much.
Direct sunlight or lighting (of an inverter
type fluorescent lamp, etc.) is striking the
remote control sensor of the main unit.
Remote control is being used near TV set
with a remote control sensor.
What to Do
Play another disc.
Load disc with label side facing upward.
Clean disc.
Select the CD/Video CD player by pressing INPUT
or button until “VCD/CD” lights up on the display.
Clean disc.
Lower volume.
Set the TV MODE switch to proper position.
Tighten slack with a pencil (pen) before using.
Replace tape or cover erasure prevention hole with
adhesive tape.
Clean heads.
Clean heads.
Replace tape.
Press the DOLBY NR button to turn it on.
Press the DOLBY NR button to turn it off.
Demagnetize heads with head demagnetizer.
Tighten slack with a pencil (pen) before using.
Replace tape.
Do not use endless tapes.
The function of searching for the beginning of desired
selections will not operate unless the silent gaps
between selections are at least four seconds long.
Wind the unrecordable part of the tape and start
recording from the recordable part.
Replace batteries.
Use within 6 m and 60° radius.
Reposition the main unit.
Relocate the main unit away from the TV.
Tape deck
Appendix
Remote control
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha GX-707RDS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha GX-707RDS in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info