48738
282
Zoom out
Zoom in
Previous page
1/304
Next page
282
Appendix
How to Install the
EXDGO1 in the EX5/7
Necessary Items
EXDGO1 (Digital Output Board) x 1
Flat cable x 1 (included in the EXDGO1 package)
Installation
You can install the EXDGO1 after removing the
optional board cover. For more information on
removing the optional board cover, see How to Remove
the Optional Board Cover.
If the ASIB1 (SCSI Interface Board) is already
installed, it must first be removed before proceeding.
If you want to install the two boards simultaneously,
first install the EXDGO1.
When installing the optional board (from when you
remove the cover to when the cover is replaced
securely) all operations must be done with the power
cord disconnected.
The procedure for installing the EXDGO1 is the same
as for the EXIDO1. Refer to How to Install the
EXIDO1 in the EX5/7.
For information on Word Clock settings, see Utility mode
(page 277).
When the EXDGO1 is properly installed, L and R
signals will be output digitally.
When connecting the EXDGO1 (Digital Output AES/EBU
[XLR] jack) and an external audio device, use the XLR
cable with the impedance characteristics, 110
When receiving word clock from an external audio device,
you are required to connect the EXDGO1 (Word Clock In
[BNC] jack) and the external audio device. In this case, use
the BNC connector/coaxial cable with the impedance
characteristics, 75
How to Install the ASIB1
in the EX5/7
Necessary Items
ASIB1 (SCSI Interface Board) x 1
SCSI cable (Flat cable 50P; length: 280mm) x 1
(included in the ASIB1 package)
Cutting pliers or scissors (to cut a cable)
When you open the package of the ASIB1 board, you
will find two SCSI cables connected to the ASIB1,
and two (2-pin) power cables, one is plugged to the
ASIB1 and the other is left unplugged. To install the
ASIB1 into the EX, only the short (280mm long)
SCSI cable is used. First, it is necessary to remove
the long (480mm long) SCSI cable and 2-pin power
cable from the ASIB1 board.
Installation
You can install the ASIB1 after removing the optional
board cover. For more information on removing the
optional board cover, see How to Remove the Optional
Board Cover.
When two boards are installed simultaneously such as
the ASIB1 and EXIDO1 (or EXDGO1), first install the
EXIDO1 (or EXDGO1).
When installing the optional board (from when you
remove the cover to when the cover is replaced
securely) all operations must be done with the power
cord disconnected.
1 Remove the two screws from the ASIB1 opening cover (hold
the cover from inside the EX5/7 as you remove the cover).
The two screws will be used again when securing the ASIB1.
Be careful not to lose them.
After you take off the cover, do not leave it inside the
EX5/7 and put it in a safe place.
2Disconnect the long (480mm long) SCSI cable from
the connector (CN1) on the ASIB1 board.
Opening cover
Option/E/qx 5/21/98 11:58 AM Page 282
282


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha EX7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha EX7 in the language / languages: English as an attachment in your email.

The manual is 7,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha EX7

Yamaha EX7 User Manual - German - 302 pages

Yamaha EX7 User Manual - Dutch - 302 pages

Yamaha EX7 User Manual - French - 302 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info