48738
276
Zoom out
Zoom in
Previous page
1/304
Next page
276
Utility Mode
Touch EG
You can express the portion “A” with the velocity and “B”
with the aftertouch.
Scene Controller Assign
Sets the controller for Scene Control. You can select
Modulation Wheel 2 or Foot Controller.
Settings: MW2 (Modulation Wheel 2), FC (Foot
Controller)
For more information on Scene Control, see page 57.
Ribbon Controller Mode
Sets whether the Ribbon Controller value returns to
a center value when you release your finger from the
Ribbon Controller (reset), or the value is retained at
the value that your finger held before releasing
(hold).
Settings: hold, reset
This parameter is not available with EX5R.
[F6]: OTHER (Other Setup)
The “Other” Setup allows you to make misllaneous
settings that are applied to the entire system.
Effect Bypass
Selects the type of effect that is by-passed (the effect
is not applied) when [EF BYPASS] ([BYPASS] on the
EX5R) is pressed on the front panel.
Settings: Rev (Reverb), Cho (Chorus), Ins (Insertion) each
can be set to: ¨ (Off: effect is applied), (On:
effect is by-passed)
0
AB
127
Breath
Control
Time
Memory Protect
Sets whether or not the current user Voice,
Performance, and Pattern data are protected. When
set to “on,” it is not possible to store data. This
setting is used on a temporary basis when you don’t
want to lose user data.
Settings: on, off
Edit Confirm
Sets whether or not the “Are you sure?”
confirmation message will be displayed when you
execute a Job or store data. You may want to skip the
confirmation when you are accustomed to the EX
operations. When set to “on,” the message will be
displayed, and when set to “off,” the message will
not be displayed.
Settings: on, off
SCSI ID
Sets the SCSI ID number for the EX. The EX’s SCSI
ID number is set to “2” when shipped from the
factory. When connecting the EX to a SCSI device
with the same SCSI ID number, it is necessary to
change one of the devices’ ID number.
This “SCSI ID” parameter is not displayed or selected
unless you install an optional ASIB1 SCSI Interface
board.
To connect an external SCSI device to the EX, it is first
necessary to install the separately sold ASIBI (SCSI
board).
When you change the SCSI ID number, it is necessary
for you to turn the power off and back to on again, to
make the change effective.
Settings: 0~7
Utility/E/qx 5/21/98 11:55 AM Page 276
276


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha EX7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha EX7 in the language / languages: English as an attachment in your email.

The manual is 7,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha EX7

Yamaha EX7 User Manual - German - 302 pages

Yamaha EX7 User Manual - Dutch - 302 pages

Yamaha EX7 User Manual - French - 302 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info