464180
17
Zoom out
Zoom in
Previous page
1/150
Next page
Quick start guide
17 En
Introduction
1 Turn on the video monitor connected to this unit.
2 Press
B
MASTER ON/OFF inward to the ON
position on the front panel.
After this unit is turned on, it takes approximately 20 seconds until this
unit produces sounds, and while “Please wait” appears in the front
panel display, this unit does not accepts the front panel operations and
stores the remote control operations. This unit performs the stored
remote control operations after “Please wait” disappears.
3 Rotate the
D
INPUT selector to set the input source
to “BD/HD DVD”.
y
The recommended sound field program is set for each input source
(BD/HD DVD, etc.). You can also use various sound field programs
and other sound modes for playback. Refer to the following pages for
details:
see pages 60 and 72 to use various sound field programs
see page 60 to turn on or off the sound effect
see page 61 to use the pure direct mode for high fidelity sound
4 Start playback of the desired Blu-ray Disc/HD DVD
source on your player.
5 Rotate
E
VOLUME to adjust the volume.
After using this unit...
Press
A
MAIN ZONE ON/OFF to set this unit to the
standby mode.
This unit is set to the standby mode and consumes a small amount
of power in order to receive infrared signals from the remote
control. To turn on this unit from the standby mode, press
A
MAIN
ZONE ON/OFF on the front panel (or
E
POWER on the remote
control). See page 39 for details.
Are you enjoying playback?
If there are some troubles with playback, check the settings as
follows.
No sound is output.
Are the speakers connected correctly?
 Check the speaker connection.
Are Your Blu-ray Disc/HD DVD player connected correctly?
 Check the connection of the Blu-ray Disc/HD DVD player.
Are the front speakers selected correctly?
 Press GSPEAKERS A or GSPEAKERS B.
Is volume setting correct?
 Adjust the volume level.
Does the Blu-ray Disc/HD DVD player play back correctly?
 Check the setting of the Blu-ray Disc/HD DVD player.
No picture.
Is the video monitor connected correctly?
 Check the connection of the video monitor.
If the video monitor is connected to the HDMI OUT 1 jack of
this unit, is the “HDMI OUT SEL” setting correct?
 Set the operation mode selector to FAMP and then press
CHDMI OUT repeatedly to set “HDMI OUT SEL” to
“OUT 1”.
Is Blu-ray Disc/HD DVD player connected correctly?
 Check the connection of the video monitor.
Is the input source setting of the video monitor correct?
 Check the setting of the input source of the video monitor.
Any other troubles?
Refer to “Troubleshooting” on pages 122 to 127 for other
troubles.
Step 3: Turn on the power and start
playback
Check the type of the connected speakers.
If the speakers are 6-ohm speakers, set “SPEAKER IMP.” to
“6 MIN” before using this unit (see page 119).
Note
Automatic setup feature
To optimize the speaker settings for your listening room, use the
automatic setup feature. See pages 43 to 48 for details.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DSP-Z11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DSP-Z11 in the language / languages: English as an attachment in your email.

The manual is 4,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha DSP-Z11

Yamaha DSP-Z11 User Manual - German - 150 pages

Yamaha DSP-Z11 User Manual - Dutch - 150 pages

Yamaha DSP-Z11 User Manual - French - 150 pages

Yamaha DSP-Z11 User Manual - Italian - 150 pages

Yamaha DSP-Z11 User Manual - Swedish - 150 pages

Yamaha DSP-Z11 User Manual - Spanish - 150 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info