557503
45
Zoom out
Zoom in
Previous page
1/576
Next page
43
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
3 Place this remote control and the other
remote control about 5 to 10 cm apart on a
flat surface so that their infrared transmitters
are aimed at each other.
4 Press LEARN by using a ballpoint pen or
similar object.
Notes
Complete each of the following steps in 30 seconds. Otherwise,
the learning mode will be automatically canceled. In this case,
press LEARN again.
Do not press and hold LEARN longer than 3 seconds.
Otherwise this unit enters the manufacturer code setting mode.
5 Press the button for which you want to
program the new function.
LEARN is displayed.
LEARN
5 Press LEARN again to exit from the setup
mode.
Notes
Supplied remote control does not store all the manufacturer
codes for commercially available AV components (including
Yamaha AV components). Therefore it may not work to operate
your AV component. If operation is not possible with any of the
manufacturer codes, program the new remote control function
with the Learn feature or use the remote control for the
component.
If you have already programmed a remote control function for a
button, the function by learning programming takes priority
over the setup manufacturer codes function.
•“ERROR appears in the display window when pressing
buttons other than indicated in each step, or more than one
button at once.
Learn Feature
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote controls functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
Programming a new remote
control function
1 Set 10KEY/DSP to 10KEY.
Note
It is also possible to program in the control area of this unit
with 10KEY/DSP set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
2 Press an input selector button, Å or ı to
select a source component.
5 to 10 cm (2 to 4 inch)
TRANSMIT
RE-NAME
STANDBY
6CH INPUT
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
SOURCE
ENTER
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
POWER
LEARN
DSP
10KEY
Flashes alternately
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-A UX
TRANSMIT
RE-NAME
STANDBY
6CH INPUT
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
SOURCE
ENTER
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
POWER
0108DSPAZ2_41-54_EN(GB) 02.8.22, 0:16 PM43
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DSP-AZ2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DSP-AZ2 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 11,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info