557503

Yamaha DSP-AZ2 Manual

22
Zoom out
Zoom in
Previous page
1/576
Next page
20
CONNECTIONS
Connecting to an External
Amplifier
If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the PRE OUT/MAIN IN jacks as follows.
Notes
• When RCA pin plugs are connected to the PRE OUT/MAIN
IN jacks for output to an external amplifier, it is not necessary
to use the corresponding SPEAKERS terminals. Set the volume
of the amplifier connected to this unit to the maximum.
• No signals will be output from any other PRE OUT jacks than
the MAIN jacks when SPEAKER A is turned off with ZONE B
selected for “1H SP B SET” on the SET MENU.
1 FRONT EFFECT jacks
Front effect channel line output jacks.
2 REAR (SURROUND) jacks
Rear channel line output jacks.
3 SUBWOOFER jacks
When using a subwoofer with built-in amplifier, including
the YAMAHA Active Servo Processing Subwoofer
System, connect the input jack of the subwoofer system
to this jack. Low bass signals distributed from the main,
center and/or rear channels are directed to this jack if they
are assigned to this jack. (The cut-off frequency of this
jack is 90 Hz.) The LFE (low-frequency effect) signals
generated when Dolby Digital or DTS is decoded are also
directed if they are assigned to this jack.
Notes
• Adjust the volume level of the subwoofer with the control on
the subwoofer. It is also possible to adjust the volume level by
using the remote control of this unit (see “ADJUSTING THE
LEVEL OF THE EFFECT SPEAKERS” on page 67).
• Depending on the settings of “1 SPEAKER SET” and “10 LFE
LEVEL” on the SET MENU, some signals may not be output
from the SUBWOOFER jack.
Connecting to the 6CH INPUT
Jacks
This unit is equipped with 6 additional input jacks (left
and right MAIN, CENTER, left and right SURROUND
and SUBWOOFER) for discrete multi-channel input from
an external decoder, sound processor or pre-amplifier.
Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.
Notes
• When 6CH INPUT is selected, the signals input to the 6CH
INPUT jacks have priority over any other input source.
• When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.
• When you select 6CH INPUT as the input source, settings of
“1 SPEAKER SET (1A to 1E)” on the SET MENU do not
apply.
• When headphones are used, only main L/R channels are
output. The setting for “6CH INPUT SET” on the SET MENU
will not be applied.
• Setting for “15 6CH INPUT SET” on the SET MENU will be
applied when 6CH INPUT is selected.
MAIN
IN
OUT
PRE OUT/MAIN IN
SUB
WOOFER
CENTER
REAR
FRONT EFFECT
REAR CENTER
R
L
R
L
(SURROUND)
6
1
2
3
4
5
4 REAR CENTER jack
Rear center channel line output jack.
5 MAIN jacks
IN: Line input to this unit’s main channel amplifiers.
When connecting to these jacks, signals input to the
preamplifier of this unit will not be output from the main
amplifier of this unit.
OUT: Main channel line output jacks.
Note
• The signals output through these jacks are affected by the
BASS, TREBLE and BASS EXTENSION settings.
6 CENTER jack
Center channel line output jack.
0103DSPAZ2_10-22_EN(GB) 02.8.22, 0:15 PM20
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DSP-AZ2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DSP-AZ2 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 11,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info