464179
70
Zoom out
Zoom in
Previous page
1/110
Next page
E-68
REMOTE CONTROL FEATURES
Programming a new remote control function (Learn feature)
If you want to program functions not included in the basic operations covered by the manufacturer code, or a manufacturer code is not
available, the following procedure needs to be performed. The possible programming area is the same as a component control area, so the
buttons are programmable independently for each source component area.
TRANSMIT RENAME
CLEAR LEARN MACRO OFF ON
MACRO
SYSTEM
POWER
STANDBY
VAUX TUNER PHONO
CABLE SAT MD/TAPE CDR CD
DTV/LD VCR 1 VCR 2 VCR3/DVR DVD
6CH INPUT
TITLE
SOURCE
SEARCH
POWER STOP PAUSE PLAYREC
CHAPTER
SELECT
10KEY DSP
HALL 1 HALL 2 CHURCH JAZZ CLUB
ROCK
ENTER
CONCERT
CONCERT
ENTER
DISPLAY
MENU
SOUND
1234
4, 8
2
1
1
1
Set 10KEY/DSP to 10KEY.
Caution
• It is also possible to program in the control area of this unit
with 10KEY/DSP set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
2
2
Press an input selector button to select a source
component.
3
3
Place this remote control and the other remote
control about 5 to 10 cm apart on a flat surface so
that their infrared transmitters are aimed at each
other.
4
4
Press LEARN by using a ballpoint pen or similar
object.
“LEARN” and the selected component name appear alternately
in the display window.
10KEY DSP
TRANSMIT RENAME
CLEAR LEARN MACRO OFF ON
MACRO
SYSTEM
POWER
STANDBY
VAUX TUNER PHONO
CABLE SAT MD/TAPE CDR CD
DTV/LD VCR 1 VCR 2 VCR3/DVR DVD
6CH INPUT
TITLE
5 to 10 cm (2 to 4 inch)
LEARN
LEARN
DVD
Cautions
• If you do not press any button within 30 seconds during steps
5 and 6, the learning process is canceled. If this happens, start
over from step 4.
• Do not press and hold LEARN longer than 3 seconds.
Otherwise this unit enters the manufacturer code setting
mode.
5
5
Press the button for which you want to program the
new function.
“LEARN” is displayed.
6
6
Press and hold the button on the other remote
control that has the function you want to program
into this remote control until OK appears in the
display window.
Cautions
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 5.
• When the memory is full, “FULL” appears in the display
window, and this remote control cannot acquire any more
functions. Clear unnecessary programmed functions to allow
the unit to acquire new functions.
7
7
Repeat steps 5 and 6 to program additional func-
tions.
8
8
Press LEARN again to exit from the learning mode.
Cautions
Learning may not be possible in the following cases:
1 when the batteries in the remote control for this unit or other
component are weak
2 when the distance between the two remote controls is too
much or too little
3 when the remote control infrared windows are not facing with
appropriate angle
4 when the remote control is exposed to the direct sunlight
5 when the function to be programmed is continuous or
uncommon
“ERROR” appears in the display window in the following
circumstances:
1 when pressing more than one button at once
2 when MACRO ON/OFF is switched to another position
LEARN
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DSP-AZ1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DSP-AZ1 in the language / languages: English as an attachment in your email.

The manual is 5,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha DSP-AZ1

Yamaha DSP-AZ1 User Manual - English - 110 pages

Yamaha DSP-AZ1 User Manual - German - 110 pages

Yamaha DSP-AZ1 User Manual - Dutch - 110 pages

Yamaha DSP-AZ1 User Manual - French - 110 pages

Yamaha DSP-AZ1 User Manual - Italian - 110 pages

Yamaha DSP-AZ1 User Manual - Swedish - 110 pages

Yamaha DSP-AZ1 User Manual - Spanish - 110 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info