557382
41
Zoom out
Zoom in
Previous page
1/78
Next page
39
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
5 Press the button for which you want to
program the new function.
LEARN is displayed.
6 Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until OK appears in the display window.
Notes
•“NG appears in the display window when programming has
not been done correctly. In this case, start over from step 5.
This remote control can learn approximately 120 functions.
However depending on the signals learned, FULL may
appear in the display window much earlier than this number. In
this case, clear unnecessary programmed functions to make
further learning on the remote control.
7 Repeat steps 5 and 6 to program additional
functions.
8 Press LEARN again to exit from the learning
mode.
Notes
It is also possible to program in the control area of this unit
with 10KEY/DSP set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
If the batteries in the other remote control are weak, they may
not have enough power to transmit signals to this remote
control.
When the remote controls are either too close together or too
far apart, you may not be able to program this remote control.
Direct sunlight interferes with infrared rays.
•“ERROR appears in the display window in the following
circumstances:
when pressing more than one button at once; or
when MACRO ON/OFF is switched to another position.
Programming a New Remote
Control Function (Learn Feature)
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote controls functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
1 Set 10KEY/DSP to 10KEY.
2 Press an input selector button, Å or ı to
select a source component.
3 Place this remote control and the other
remote control about 5 to 10 cm apart on a
flat surface so that their infrared transmitters
are aimed at each other.
4 Press LEARN by using a ballpoint pen or
similar object.
Do not press and hold LEARN longer than three
seconds. Otherwise this unit enters the manufacturer
code setting mode.
Note
If you do not press any button within 30 seconds during steps 5
and 6, the learning process is canceled. If this happens, start
over from step 4.
TRANSMIT
RE-NAME
STANDBY
6CH INPUT
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
SOURCE
ENTER
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AU X
POWER
5 to 10 cm (2 to 4 inch)
TRANSMIT
RE-NAME
STANDBY
6CH INPUT
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
ENTER
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AU X
POWER
LEARN
LEARN
TRANSMIT
RE-NAME
STANDBY
6CH INPUT
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
SOURCE
ENTER
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AU X
POWER
DSP
10KEY
Flashes alternately
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-A UX
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DSP-AX3200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DSP-AX3200 in the language / languages: English as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha DSP-AX3200

Yamaha DSP-AX3200 User Manual - German - 78 pages

Yamaha DSP-AX3200 User Manual - Dutch - 78 pages

Yamaha DSP-AX3200 User Manual - French - 78 pages

Yamaha DSP-AX3200 User Manual - Italian - 78 pages

Yamaha DSP-AX3200 User Manual - Swedish - 78 pages

Yamaha DSP-AX3200 User Manual - Spanish - 78 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info